manualshive.com logo in svg

Eliwell EWCM 4120, Руководство пользователя, Страница: 49 / 75

Поделиться
Скачать
Eliwell EWCM 4120 Скачать руководство пользователя страница 49

 

49 

Fans thermal switch 

The intervention of the digital fan thermal protection is blocked for the correctly used fan.  

If another fan is available it will be selected depending on the policy (Fn11) and immediately activated. The 

contemporaneous intervention of the thermal protections of all of the digital fans causes an alarm which blocks the 

machine. 

In the case of fans with continuous control or digital fans in which a single common thermal fan has been configured, 

the tripping of the thermal switch causes the machine to shut down. 

 

ADVANCED FUNCTIONS 
On/off device  

The activation/deactivation of the device used for controlling resources may be carried out via keyboard or digital 

input: 

 

ON/OFF from keyboard

: The device may be switched on or off using the keyboard from the Folder 

Programming menu 

OP

. This function is not active if the ON/OFF is configured via digital input (e.g. for DI5, 

CF20=13). In OFF mode, the screen will display the word 

OFF.

 

 

ON/OFF via Digital Input

: If a digital or analogue input is configured for this function, the device state 

depends on the input state. In OFF mode, the word 

OFF 

will flash on-screen. ON/OFF via keyboard is not 

active. 

Содержание EWCM 4120












































































Отзывы:

Нет отзывов