Eliwell EWCM 4120 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 75

Eliwell EWCM 4120 Скачать руководство пользователя страница 56

56

Code Action

Notes

Er03 Blocks all compressors and fans

Er04

Blocks all compressors and fans:
- at maximum power (Fn22) in Cool
- OFF in Heat

AL04 is loaded for digital fans whenever a fan is
activated/deactivated, except when the deactivation is due to
the alarm itself; for the inverter fan when activated. If delivery
probe error occurs, minimum alarm is always signalled.

Er05

Blocks all compressors and fans:
- at maximum power (Fn22) in Cool
- OFF in Heat

If inlet probe error occurs, management alarm disabled

Er06 Blocks all compressors and fans

If inlet probe error occurs, management alarm disabled

Er07

Blocks all compressors and fans:
- at maximum power (Fn22) in Cool

- OFF in Heat

If outlet probe error occurs, management alarm disabled

Er08 Blocks all compressors and fans

If outlet probe error occurs, management alarm disabled

Er09  Exclude compressor 1
Er10  Exclude compressor 2
Er11  Exclude compressor 3
Er12  Exclude compressor 4
Er13  Exclude continuous compressor

AL14 is loaded on activation of the block digital input

Er14  Exclude fan 1
Er15  Exclude fan 2
Er16  Exclude fan 3
Er17  Exclude fan 4
Er18  Blocks the system

AL16 is loaded on activation of the block digital input

«
...
54
55
56
57
58
...
»

Содержание EWCM 4120












































































Отзывы:

Нет отзывов