12
Description of the hood
1
2
4
4
5
6
7
3
1. Blower and light controls
2. Halogen
lamps
3. Grease filter Handle
4. Grease
filter
5. Canopy
6. Duct
covers
7. Recirculating grid (only for
recirculating version)
Control
CFM
REDUCTION
SYSTEM
Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
Note: Hood retains last speed setting when aspiration
switch is turned off.
Description of control panel
CHARCOAL FILTER GREASE FILTER
3
1
5
2
4
1. Light Button
đƫ
Press lamp button to turn ON the light on High Intensity
(Lamp state previously OFF).
đƫ
Press lamp button to turn ON the light on Low Intensity
(Lamp state previously ON).
đƫ
Press lamp button to turn OFF the light (Lamp state
previously
ON).
2. Timer Button
đƫ
The default timer setting is 10 minutes, and it can be
adjusted between 60 minutes and 1 minute.
đƫ
After pressing the timer button, the control enters to a
timer setup mode, and user can adjust the timer
countdown time with the “+” and “-” buttons within 5
seconds. The timer can be initiated immediately pressing
the timer button, after setting the timer duration or
pressing the timer button twice (default 10 minutes
setting).
đƫ
If no action occurs within 5 seconds, the countdown
will
start.
đƫ
During the timer setup the “+” and “-” buttons are
dedicated to the timer and no motor action will occur.
đƫ
Once the timer is initiated, it can be cancelled by
pressing the timer button again.
3. Display
đƫ
Shows the hood settings.
đƫ
The display will be lit at low intensity when the hood
is not operating.
đƫ
Pressing any key the display will light up at high intensity.
đƫ
The display will be lit at high intensity when the hood
is
operating.
đƫ
If no key is pressed within a minute the display will return
to being lit at low intensity.
4. “-” Button. Speed Decrease / OFF
đƫ
This button is used to decrease the fan speed, or turn
OFF the fan.
đƫ
The fan will turn OFF if the “-” button is pressed and
the hood was in the first speed.
đƫ
If the fan is at second speed and the “-” button is
pressed, the fan will be set to first speed.
đƫ
If the fan is at third speed and the “-” key is pressed,
the fan will be set to second speed.
đƫ
If the fan is at fourth speed and the “-” button is
pressed, the fan will be set to third speed.
đƫ
If the fan is OFF and the “-” button is pressed, the
control backlight will light up.
5. “+” Button. Speed Increase / ON
đƫ
This button is used to increase the fan speed, or turn
ON the fan.
đƫ
The fan will turn ON if the “+” button is pressed and the
hood was OFF.
đƫ
If the fan is at first speed and the “+” button is pressed,
the fan will be set to second speed.
đƫ
If the fan is at second speed and the “+” button is pressed,
the fan will be set to third speed.
đƫ
If the fan is at third speed and the “+” button is pressed,
the fan will be set to fourth speed.
đƫ
If the fan is at fourth speed and the “+” button is pressed,
a beep will sound.
Clock programming
đƫ
The clock can be reprogrammed at any time except
during an active timed function.
đƫ
The clock can be displayed in a twelve hour format and
valid clock times are from 1:00 to 12:59.
đƫ
The clock can be reprogrammed pressing the “Timer”
button for 3 seconds, and after, the clock can be
adjusted with the “+” and “-” buttons.
đƫ
The user can have minute increments / decrements of
1 minute, but if the user keep pressing the “+” / ”-”
buttons for more than 1 second, the increments /
decrements will be of 5 minutes.
đƫ
During this option the control will round to the nearest
5
minutes.
đƫ
The user can finish on reprogramming the clock
pressing the “Timer” button.
đƫ
After 1 minute of no button pressed the control will
accept the programmed clock time and will add one
minute to the set clock.
