background image

GB-12

GB

Operating voltage

3 V DC

Battery type

CR 2032

Protection class

IP 20

Permitted ambient temperature

0° to +50 °C

Radio frenquency

868,3 MHz

Deletion of individual transmitters

1. Open the front cover and press 

simultaneously

:

• Programming button 

P

STOP

-button

2. Hold down this button combination until the LED goes out

briefly.

Deletion of all transmitters

1. Open the front cover and press 

simultaneously

:

• Programming button 

P

UP

-button

STOP

-button

DOWN

-button

2. Hold down this button combination until the LED goes out

briefly 3 times.

Technical data

The maximum sending range within a building is up to 20 m and
in the open air up to 150 m.

GB-11

Deletion of radio/technical data 

Battery changing/Cleaning/Troubleshooting

Changing the battery 

1. Push the wall transmitter up out

of the wall holder.

2. Remove the battery.
3. Insert a new battery 

correctly

.

Cleaning

Clean the device with a damp 
cloth only.
Do not use cleaning solutions,
as these may damage the plastic.

Notes on troubleshooting

Fault

Cause

Remedy

CR

2032

The drive does not run,
the transmission indi-
cator lamp 
doesn’t light up.

The drive does not run,
the transmission indi-
cator lamp stays on.

The automatic switch
commands are not
carried out.

Drive operates in the
wrong direction.

1. Install a new battery.

2. Install the battery

correctly.

1. Reduce distance to the

receiver.

2. Program the transmitter

Set the UniTec-868 to
"AUTO“.

Delete transmitter and
program correctly.

1. The battery is empty.

2. The battery is incorrectly

installed.

1. The receiver is outside of

sending range.

2. Transmitter not pro-

grammed into receiver.

The UniTec-868 is set to
"Manual     “ operation.

Directions are incorrectly
programmed.

General conformity declaration:

The company Firma elero GmbH herewith declares that the
UniTec-868 conforms to the basic requirements and other relevant
regulations of Directive  1999/5/EC.

Содержание UniTec-868









Отзывы: