background image

Explanation of functions

GB-6

Manual/automatic sliding switch

The receivers are switched into "

Manual

“ or "

AUTO

“.

In automatic mode the receivers react to all signals, in manual
mode only to the 

UP-STOP-DOWN

button and the wind signal.

Transmission indicator lamp

A radio signal is displayed by the lighting up of the transmission
indicator lamp.

The transmitting power or the range of transmission will be redu-
ced through the reduction in the performance of the battery. If the
indicator pilot lamp does not light up when the button is pressed
the battery must be exchanged.

Group controller

A group is understood to mean control of one or more receivers at
the same time.
The UniTec-868 can be teached-in into several receivers.

Intermediate position

The intermediate position is a freely-selectable position of the
blind/shutter betweeen the top and bottom end position. This can
be approached from the top end position after programming is
complete.

Press the 

DOWN

-button 

briefly

twice successively.

In venetian blind mode any tilting which is programmed is carried
out automatically when the blind reaches the intermediate posi-
tion.

Ventilation/Tilting

The ventilation-tilting position is a freely selectable positoin of the
blind/shutter between the top and bottom end positoin. Using
this function you can raise the roller shutter from the lower end
position until the ventilation slits are again open. With venetion
blinds, the slats are inverted.
Press the 

UP

-button briefly 

twice

successively.

GB

Installation

GB-5

Advice:

Radio systems, which operate on the same frequency,
can lead to reception of interferences.

Please note, that the range of the radio signal is
limited by the government and the built environment.

Mounting of wall bracket

• Before installing the unit at the required position, check the

proper function of the transmitter and the receiver.

• Attach the bracket to the wall with the two dowels and screws

which are provided.

• Push the UniTec-868 onto the wall bracket from above.

Содержание UniTec-868









Отзывы: