elero RolTop-915 Скачать руководство пользователя страница 8

Страница: 8 / 10

5.6.9 Option C:

Fixed upper and lower end position

Option C: Fixed upper and lower end position

①

In a medium fabric position, using the installation
cable or a programmed transmitter, press the

button

▲

until the fabric has reached the desired

upper end position (to upper limit stop).
The drive system starts, stops brie

y and starts

again (as long as the UP button

▲

is pressed).

The drive system automatically stops when reaching
the upper limit stop.

②

Keep the

DOWN

button

▼

pressed until the drive

system stops automatically.
The upper end position is set.

Optional:

Activation of the relief function for the

upper limit stop: refer to section 5.6.2.

③

Press the

DOWN

button

▼

again, until the fabric

has reached the lower end position (to bottom limit
stop).
The drive system starts, stops brie

y and starts

again (as long as the DOWN button

▼

is pressed).

The drive system automatically stops when reaching
the lower limit stop.

④

Keep the

button

▲

pressed until the drive sys-

tem stops automatically.
The lower end position is set.

Optional:

Activation of the relief function for the

lower limit stop: refer to section 5.6.3.

End position setting of option C is completed.

Fig. 11 End position setting option C:

5.6.10 Option D: Upper end position freely con

gu-

rable,

xed lower end position

Option D: Upper end position freely con

gurable,

xed lower end position

①

In a medium fabric position, using the installation
cable or a programmed transmitter, press the

button

▲

until the fabric has reached the desired

upper end position.
The drive system starts, stops brie

y and starts

again (as long as the button is pressed).
Corrections can be made with the buttons

▲

and

▼

②

Keep the

DOWN

button

▼

pressed until the drive

system stops automatically.
The upper end position is set.

③

Press the

DOWN

button

▼

again, until the fabric

has reached the lower end position (to bottom limit
stop).
The drive system starts, stops brie

y and starts

again (as long as the DOWN button

▼

is pressed).

The drive system automatically stops when reaching
the lower limit stop.

④

Keep the

button

▲

pressed until the drive sys-

tem stops automatically.
The lower end position is set.

Optional:

Activation of the relief function for the

lower limit stop: refer to section 5.6.3.

End position setting of option D is completed.

Fig. 12 End position setting option D:

8 | US+CA

elero

GmbH

End position settings

5.6.7 Option A: Upper and lower end position

freely con

gurable

Option A:
Upper and lower end position freely con

gurable

①

In a medium fabric position, using the installation
cable or a programmed transmitter, press the

button

▲

until the fabric has reached the desired

upper end position.
The drive system starts, stops brie

y and starts

again (as long as the UP button

▲

is pressed).

Corrections can be made with the buttons

▲

and

▼

②

Keep the

DOWN

button

▼

pressed until the drive

system stops automatically.
The upper end position is set.

③

Press the

DOWN

button

▼

again, until the fabric

has reached the desired lower end position.
The drive system starts, stops brie

y and starts

again (as long as the

DOWN

button

▼

is pressed).

Corrections can be made with the buttons

▲

and

▼

④

Keep the

button

▲

pressed until the drive sys-

tem stops automatically.
The lower end position is set.

End position setting of option A is completed.

Fig. 9 End position setting option A:

5.6.8 Option B:

Fixed upper end position,
lower end position freely con

gurable

Option B: Fixed upper end position,

lower end position freely con

gurable

①

In a medium fabric position, using the installation
cable or a programmed transmitter, press the

button

▲

until the fabric has reached the desired

upper end position (to upper limit stop).
The drive system starts, stops brie

y and starts

again (as long as the UP button

▲

is pressed).

The drive system automatically stops when reaching
the upper limit stop.

②

Keep the

DOWN

button

▼

pressed until the drive

system stops automatically.
The upper end position is set.

Optional:

Activation of the relief function for the

upper limit stop: refer to section 5.6.2.

③

Press the

DOWN

button

▼

again, until the fabric

has reached the desired lower end position.
The drive system starts, stops brie

y and starts

again (as long as the button is pressed).
Corrections can be made with the buttons

▲

and

▼

④

Keep the

button

▲

pressed until the drive sys-

tem stops automatically.

End position setting of option B is completed.

Fig. 10 End position setting option B:

Содержание RolTop-915











Результаты поиска

Содержание RolTop-915

Отзывы:

Бренды по названию

Популярные бренды

elero RolTop-915, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание RolTop-915

Отзывы:

Бренды по названию

Популярные бренды