elero RolMotion/D+ M Series, Инструкция по эксплуатации и сборке

Страница: 5 / 8

2 Pull out the plug.
3 Insert the motor cable plug until the lock engages.
Removing and inserting the motor cable plug
Delivery
condition
Removing plug Inserting plug
Fig. 4 Removing and inserting the motor cable plug
5.3 Connection example for RolMotion/D+ M
230 V / 50 Hz
1 0 2
reseau electrique
L
N
PE
230V/50Hz
ver
t-j
aune
br
un
no
ir
ble
u
de volet
M
1~
1 0 2
rete
L
N
PE
230V/50Hz
ver
de
/g
ial
lo
m
ar
rone
ner
o
blu
M
1~
1 0 2
Netz
L
N
PE
230V/50Hz
gr
ün/
gel
b
br
aun
sc
hw
ar
z
bla
u
oder -taster
M
1~
1 0 2
power grid
L
N
PE
230V/50Hz
gr
ee
n/
Yel
low
br
own
bl
ac
k
blu
e
junction box
M
1~
boiter de scatola di
derivatione
(3)
(2)
(1)
(3)
(2)
(1)
Fig. 5 Connection diagram RolMotion/D+ M 230 V / 50 Hz
and cable assignment when using Hirschmann plug
connection STAS-3
Important
The motor controls in the Open and Down/Closed travel
directions must be locked against each other.
A switching time of at least 0.5 seconds must be observed.
5.4 Parallel circuit
Important
You can connect up to 3 (maximum) RolMotion/D+ M in
parallel. Please note the maximum switching capacity of
the control unit.
However, the behaviour of the devices is not synchronous.
Do not connect the RolMotion/D+ M drive in parallel with
other drives (e.g. elero RolTop M).
5.5 Commissioning
Important
The drive is in commissioning mode when delivered.
► The end positions may need to be adjusted using the
elero assembly cable (see Fig. 6).
► The assembly cable may only be connected to commis-
sion the drive and for adjustment operations
→
1
→
2 →
3
5.5.1 Connection for assembly cable
%ODX1HXWUDOOHLWHU
6FKZDU]
%UDXQ
*UQJHOE
HOHUR HOHUR
%ODX1HXWUDOOHLWHU
6FKZDU]
%UDXQ
*UQJHOE
Fig. 6 Connection for assembly cable
► Switch on mains.
► You can now set the end positions with the elero assem-
bly cable.
5.5.2 Automatic configuration of end positions
Important
To use travel profiles, the upper and lower end positions
must first be set. During the “Setting the end positions” pro-
cess, the blind moves in the “Standard mode” travel profile.
Automatic programming of end positions
1 Connect the electric power in accordance with
section 5.2.
2 Check for functioning: If necessary, change or swap
the assignment of the direction buttons for the operat-
ing switch/push button.
The drive switches off automatically when the upper or
lower limit stop is reached.
The teaching process is completed due to subsequent
travel of the shutter.
5.5.3 Changing/deleting the end positions
It is not possible to change or delete individual end posi-
tions. This is always done in pairs (upper and lower end
position simultaneously).
Changing/deleting the end positions
1
Switch on mains
2
Use the assembly cable to bring the blind to a central
position.
3
Press both direction keys [ UP ▲]+[ DOWN/CLOSE ▼]
simultaneously.
The drive travels up and down briefly for approx. 5 seconds.
The end position settings have been deleted.
The end positions are configured again automatically as
described in chapter 5.5.2.
6 Travel profiles
The RolMotion/D+ M drive has two travel profiles, standard
mode and quiet mode.
6.1 Standard mode
When travelling at high speed, only the roller blind slats are
lowered slowly.
This travel is triggered by simply turning on the wall switch/
button.
6.2 Quiet mode
Travel at slow speed along the entire travel path.
© elero GmbH EN | 5
Assembly | Electrical connection | Adjusting the end positions