10 Repairs
Please contact your specialist if you have any questions.
Please always provide the following information:
• Item number and designation on the type plate
• Type of fault
• Accompanying conditions
• Your own theories regarding the cause of the problem
11 Disassembly and disposal
After unpacking, dispose of the packaging in accordance
with the valid regulations.
Dispose of the product in accordance with the relevant
regulations when you no longer need it. Disposal is partially
subject to applicable legal regulations. Bring the product to
be disposed of to authorised collection points only.
Environmental information
No superfluous packaging materials have been used.
The packaging can be easily separated into three material
types: cardboard (box), polystyrene (padding) and polyeth-
ylene (bag, protective foam).
The device is made of materials that can be reused if dis-
mantled by a specialist company. Please note the local
regulations on disposal of packaging materials and old
appliances.
On disassembly, additional dangers must be reckoned with,
which do not occur during operation.
Before disassembling the drive the system is to be mechan-
ically secured. The drive must not be forcibly disconnected
from the system.
WARNING
Risk of injury due to electric current.
Risk of electric shock.
►
Separate power supply cables physically and discharge
any energy accumulators still charged. After switching off
the device, wait at least 5 minutes so that the motor can
cool down and the voltage can be discharged from the
capacitors.
►
During disassembly work above head height, use suita-
ble, inspected and structurally stable climbing aids.
►
Work on the electrics may only be performed by person-
nel described in the section “Safety notes on electrical
installation”.
Removal for scrap
The international, national and regional laws and regula-
tions prevailing at the time of scrapping the product must be
observed.
Ensure that materials and components are recycled, dis-
mantled and separated properly in addition to observing the
environmental and health hazards relating to recycling and
disposal.
CAUTION
Environmental damage in case of incorrect disposal
►
Electrical scrap and electronic components must be
handled as special waste and may only be disposed of by
approved specialist companies.
►
Groups of materials such as various types of plastics and
metals must be separated before recycling/disposal.
6 | EN
©
elero
GmbH
End position settings | Travel profiles
This travel is actuated by “double-tapping” at power up
(On - Off - On) or during travel by switching off and on again
in the same direction of travel. The duration of the switched-
off state must be more than one second.
To change to the standard mode travel profile, the drive
must be switched off for one second.
The quiet mode travel profile is not available during the
“Setting the end positions” operation.
7
Troubleshooting
Problem /
Error
Possible cause Remedial ac-
tion
• The drive does
not start up
• No power
supply
• Drive over-
heated
• Check connec-
tion and elec-
trical voltage
• Allow drive to
cool down
• Drive runs only
in one direction
• Faulty connec-
tion
• Error when
programming
the end posi-
tions
• Check connec-
tion
• Re-program
the end posi-
tions
• Drive stops
during travel
• End positions
incorrectly
programmed
• Travel to
intermediate
position
• Re-program
the end posi-
tions
• Drive stops
during travel
and then goes
in the opposite
direction
• Blind only
moves with
difficulty
• Obstacle in
drive path
• Check the
smooth run-
ning of the
blind
• Re-program
the end posi-
tions
• Drive only
moves in
standard mode
• End positions
are not yet
programmed
• Perform at
least two
complete
movements
in the up and
down direction
without inter-
ruption
Fig. 7 Troubleshooting the RolMotion/D+ M
8
Servicing
The RolMotion/D+ M is maintenance-free.
9
Service/manufacturer's address
If malfunctions occur or the device is damaged despite
correct handling, contact your contractor.
elero
GmbH
Antriebstechnik
Maybachstr. 30
73278 Schlierbach
Deutschland / Germany
Fon:
+49 7021 9539-0
Fax:
+49 7021 9539-212
www.elero.com
Please visit our website if you require a contact partner
outside Germany.
