Damage to the drive due to the effect of impact forces.
►
Slide the drive into the shaft. Never knock the drive in or
use force!
►
Take care not to drop the drive!
Damage or destruction to the drive by drilling.
►
Never drill the drive!
Important
Only fasten the RolMotion/D+ M to the designated fasten-
ing elements.
Fixed installed control devices need to be attached so they
are visible.
• The blind must be attached to the winding shaft.
•
The profile tube must have sufficient clearance from the
motor tube.
•
Make sure there is sufficient axial play (1 - 2 mm)
Installation in profile tubes
Ⓐ
Push drive with relevant adapter and
crown into the profile tube.
Install the motor cable so it is pro-
tected to prevent damage from the
driven part.
Ⓑ
Secure the counterpart support to
prevent axial movement, e.g. screw
or rivet on the idler.
Secure the drive axially in the
support!
Ⓒ
Attach the blind to the shaft.
Only operate the drive horizontally, as intended, with the
connection cable leading out from the side and out of the
blind winding area.
5.2 Electrical connection
WARNING
Faulty electrical connections constitute a fatal hazard.
Risk of electric shock.
►
Prior to initial commissioning, check the PE wire is cor-
rectly connected.
ATTENTION
Damage to the RolMotion/D+ M due to incorrect electrical
connection.
►
Prior to initial commissioning, check the PE wire is cor-
rectly connected.
Ingress of moisture will damage or even destroy the
RolMotion/D+ M.
►
For devices with protection class IP 44, the custom-
er-side connection of the cable ends or plugs (cable feed-
through) can also be implemented according to protection
class IP 44.
Damage or destruction of the RolMotion/D+ M for variants
with 230 V ~ due to incorrect activation.
►
Switches with an OFF presetting (dead-man's switches)
for drives are to be attached within visible range of the
RolMotion/D+ M but away from spontaneously moving
parts and at a height of more than 1.5 m.
Connect only in de-energised state. To do this, switch
the drive cable so it is de-energised.
1
Press locking mechanism on the motor cable plug to-
wards the cable using a suitable screwdriver.
4 | EN
©
elero
GmbH
Assembly | Mechanical fastening
Possible danger due to parts that are faulty becoming ener-
gised.
►
The drive falls under protection class I (protective con-
ductor system). All housing parts of the drive capable of
conducting electricity are connected with the protective
conductor system of the fixed electrical installation, which
is located at potential earth. The protective conductor
connection is designed so that, the first time the plug is
inserted, it is connected first and, in case of any damage,
it is disconnected last. The connecting cable is fitted with
mechanical strain-relief when inserted in the drive. If the
cable is torn out, the protective conductor will be torn off
last. If, in case of a fault, a live cable comes into contact
with the housing, which is connected with the protec-
tive conductor, a short circuit will generally arise so that
the fuse itself is triggered and de-energizes the electric
circuit. No electricity will be conducted to human beings
in case of a fault. 4-core connecting cables (4 x 0.75 mm
2
cross-section with black
CONINVERS
plug) are used for
the electrical connection with an earthing contact that is
conducted to the exterior.
CAUTION
Risk of injury due to malfunctions as a result of incorrect
assembly.
Drive is overwound and may destroy parts of the application.
►
For safe operation, the end positions need to be set/taught.
►
Manufacturer training is available for specialist companies.
ATTENTION
Power failures, breaking of machine parts and other mal-
functions.
►
For safe operation, assembly must be correct and the
end position adjustments will have to be carried out upon
commissioning.
Damage to RolMotion due to ingress of moisture.
►
On devices with protection class IP 44, the ends of all
cables or plugs will need to be protected from ingress
of moisture. This measure needs to be implemented
after removing the RolMotion/D+ M from the original
packaging.
►
The drive must be installed so that it cannot get wet.
Important
In its delivery condition (factory setting), the RolMotion/D+ M
will be in commissioning mode.
►
The end positions
will need to be set (see section 5.6).
5.1 Mechanical fastening
Important preliminary consideration:
The working area around the installed drive is usually
very small. For this reason, obtain an overview of how the
electrical connection has been implemented prior to the
mechanical installation (see section 5.2) and make the
necessary changes beforehand.
ATTENTION
Crushing or tension will damage the electrical cables.
►
Install all electrical cabling so that it is not subject to any
crushing or tensile load
►
Observe the bending radii of cables (at minimum 50 mm).
►
Route connecting cables in a downward loop to prevent
water running into the drive.
