manualshive.com logo in svg

Element4 Modore 95, Руководство по установке, Страница: 60 / 64

Поделиться
Скачать
Element4 Modore 95 Скачать руководство пользователя страница 60

60

Element4 Gas Fireplaces

                                                                                                                                                    

 

European

Home

.com

APPENDIX THREE

LP (PROPANE) CONVERSION

APPLICABLE MODELS

 

Bidore 95, Modore 95, Trisore 95, Optica, Bioptica

CONTENTS

This LP conversion kit contains these instructions plus the 

following:

• one Pilot Orifice (stamped 

27

)

• one Main Burner Orifice (stamped 

380

)

TOOLS REQUIRED 

Converting your fireplace to LP gas requires the following tools:

- a 7 mm box/open end wrench

- a 10 mm box/open end wrench

- a 13 mm box/open end wrench

- a 17 mm box/open end wrench

- a No. 2 Phillips screwdriver

- a pair of small needle nose pliers

- a bright work light

INSTALLATION

Step 1:

 Remove the longest glass panel and carefully store it. 

Step 2:

 Remove all of the fire media.

Step 3:

 Remove hearth (bottom) panel by lifting it up and out. 

Figure 1 shows panel removed.

Step 4:

 Remove the bolts keeping the burner base attached to 

the firebox. 

Step 5:

 Loosen the top two shutter bolts (7 mm) holding each 

of the two shutters in place, remove the shutters and tighten 

the bolts. 

Compression Nut

WARNING! 

This conversion must be done by a licensed 

plumber or gasfitter. 

Turn off the gas supply before proceeding.

Begin by reading all instructions thoroughly.

Figure 1. 

Figure 2.

Figure 3. 

Orifice Locknut

Step 6:

 Remove the compression nuts (17 mm) from each of 

the orifices and, taking care to not deform the supply tube, 

slide the supply tube out of the orifice. 

Step 7:

 Loosen the orifice locknut (Figure 3, 13 mm) and un-

screw the NG burner orifice from each of the burners

Step 8:

 Screw the LP orifice into each burner until the orifice is 

aligned with the supply tube. See Figure 3.

Step 9:

 Connect the supply tubes to each of the burner orifices 

and tighten the compression nuts. 

Step 10:

 Tighten the orifice locknuts.

Orifice and Shutter

Burner Orifice

Supply Tube

Shutter

Shutter Bolts

Содержание Modore 95

































































Отзывы:

Нет отзывов