Elektronikbau- und Vertriebs CETA 101 Скачать руководство пользователя страница 15

Страница: 15 / 23

Parameter description

Display

Designation

Description

08:18

Back Cooling

Setting range:

OFF (----), 5 ... 50K

Differential

Factory setting: OFF

Function: If temperature F1 is over the 08:08 value and temperature F3

is under 40

C, then the pump starts working, until F1 difference (08:18)

drops under 08:08 value.

08:19

Burner Block

Setting range:

OFF (----), 5 ... 80

temperature

Factory setting:

OFF

Function: Additionally or alternatively to 08:09, is possible to
regulate an F1 temperature, that is going to block burner (via
data bus). If the 08:19 value drops under 5K, the burner is
being activated again.

08:20

Thermostat

Switch – On
temperature

Setting range: 5

C… (switch – off temperature – 3K)

Factory setting: 30

Function: If F3 temperature drops under the setting 08:20, then the pump is

being activated.

08:21

Thermostat
Switch - Off

temperature

Setting range: ( Switch – On tempe3K)… 120

Factory setting:

Function: If F3 temperature rises over the setting 08:20, then the

pump is being deactivated.

08:22

Inverse

Setting range: 0, 1

thermostat

Factory setting:

Function:

Inverts the pump function. 0 = normally close,

1 = normally open

08:23

Frost-protection

Solar collector
temperature

Setting range:

Off, -15

C… 10

Factory setting: Off
Function:

Solar pump switches on when the temperature from the solar

collector drops below the 08:23 value. The pump switches off
when solar temperature rises over the 08:23 value + 2,5K.

Содержание CETA 101
























Результаты поиска

Содержание CETA 101

Отзывы:

Похожие инструкции для CETA 101

Бренды по названию

Популярные бренды

Elektronikbau- und Vertriebs CETA 101, Руководство по эксплуатации

Результаты поиска

Содержание CETA 101

Отзывы:

Похожие инструкции для CETA 101

Бренды по названию

Популярные бренды