Electronics Line Penta Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 33

Electronics Line Penta Скачать руководство пользователя страница 5

-5-

Voice Message (3601)

The 3601 is an add-on module that enables the recording of a short message. In the
event of an alarm, the panel dials the user’s telephone number and this message is
played back. Pressing 3, 6, 9 or # on the telephone acknowledges that the message has
been received.

1.4: Remote Programming

Electronics Line’s remote programming software enables programming and operation
from a PC. The software provides a comprehensive interface to the Penta control panel,
facilitating and cutting down the time taken in programming the system. RP access is
gained using a four digit code programmed at address 57. Without this code all remote
programming and operation is restricted.

Answering Machine Override

Answering machine override enables the control panel to distinguish between regular
incoming calls and a communication attempt by the RP (remote programmer) software.
An RP call is identified by the control panel as a sequence of two calls within a 30-second
time window.

1. The control panel does not answer the first incoming call.
2. The control panel opens a 30-second time window from the moment the telephone

stops ringing.

3. The control panel answers after 1 ring and RP communication is established.

This method enables the panel to share the same telephone line with answering
machines and fax machines.

RP Callback

RP call back is a toll-saver feature that makes remote programming more cost-effective.
When the remote programmer contacts the panel, the panel hangs up and calls the
telephone number programmed at address 56.

«
...
3
4
5
6
7
...
»

Содержание Penta


































Отзывы:

Нет отзывов