Electronics Line Penta Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 33

Electronics Line Penta Скачать руководство пользователя страница 18

-18-

4.3: Programming Parameters

The following section lists the Penta’s programming parameters which are used to
configure the system. For a listing of the default parameters please contact your local
dealer.

Address 00: Communication Attempts

The control panel’s attempts to communicate with the central station are organized in
rounds. A communication round is a set of dialing attempts. If the panel does not
succeed in sending the event message to the primary number within this number of
attempts, the backup number is dialed the same number of times. A new round will
begin 30 minutes after the last dialing attempt. The number of communication rounds is
defined in the first digit of this address. The number of dialing attempts in each round is
defined in the second digit.

Note: To Disable Communications, enter 00 at this

address.

First Digit:

Communication Rounds

Enter a value between 1 – F
(F = Unlimited rounds until
communication is established)

Second Digit:

Dialing Attempts

Enter a value between 1 – F

Address 01: Miscellaneous

This address offers a number of options for the system’s setup. Enter 5 digits at this
address according to the following:

Fifth Digit:

P Key Alarm

0 - Audible
1 - Silent

First Digit:

Keypads

0 - No Keypads
1 - One Keypad
2 - Two Keypads
3 - Three Keypads

Third Digit:

Tamper Zone Definition

0 - Arm/Disarm Keyswitch
1 - Tamper Zone

Second Digit:

Keyswitch Function

0 - Latching
1 - Momentary

Fourth Digit:

E Key Alarm

0 - Audible
1 - Silent

«
...
16
17
18
19
20
...
»

Содержание Penta


































Отзывы:

Нет отзывов