background image

3

13 Amp

Fuse 

Cover

Fuse 

Blue

Brown

Cord 

Clamp

13 Amp Fuse

BEFORE YOU START

CHECK THE VOLTAGE

Before  connecting  the  cleaner  to  an  electrical  supply,  ensure  that  the  voltage  shown  on  the  rating  plate  located  beneath  the 
cleaner is of the correct voltage for your electricity supply. If it is not, do not use the cleaner but refer back to your dealer.

CONNECTING TO YOUR ELECTRICITY SUPPLY

Permanently  connected  to  the  cleaner  is  a  mains  supply  (2-core)  cable  fitted  with  a  non-rewirable  plug  incorporating  a  13A 

fuse. 
In the event of the fuse requiring replacement the fuse cover should be removed using a small screwdriver. The old fuse 

MUST

 

be replaced by a 13A ASTA approved BS1362 fuse or a BSI approved fuse.  The cover must be replaced before the plug is used 

again. In the event of loss of the fuse cover, replacements can be obtained from your Electrolux Retailers and must be of the 

same colour as indicated by the coloured insert on the base of the plug. 
If difficulty is experienced in obtaining a replacement, contact Electrolux Customer Services on 08706 055055.

In no circumstances must the plug be used without a correct fuse cover fitted.

If the plug that is fitted to your appliance is not suitable for your socket outlet, it must be cut off and the appropriate plug fitted.
Remove the fuse from the cut off plug.
The cut off plug should then be disposed of to prevent the hazard of shocks in case it should be plugged into a 13 amp socket 

in another part of your home.
The  wires  in  the  mains  cable  of  this  appliance  are  coloured  in  accordance  with  the  following  code:

      Blue:  Neutral.    Brown: 

Live.

As the colours of the wires in the mains cable of this appliance may not correspond with the coloured markings identifying the 

terminals in your plug, proceed as follows: 
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
If using a three-pin plug, do not make any connection to the terminal marked with the letter E or by the earth symbol or coloured green 

or green-and-yellow. This cleaner is double insulated and no earth connection is necessary.
It is in your interest to ensure that the plug is correctly attached to the mains cable. In case of doubt, consult a qualified electrician, as 

Electrolux cannot regard the repair of faults on the plug connection as a service that can be given free of charge under the terms of 

the guarantee.

The symbol         on the product or on its packaging indicates that this product may not be treated as household waste. 

Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By 

ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and 

human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed informa-

tion about recycling of this product, please contact your local city office, your household waste disposal service or the shop 

where you purchased the product.

Содержание Z5600 Series

















Отзывы: