18
Fitting/installation: flush mounting in stone working
surfaces
When fitting in combustible material the NIN 2000,
section 4.2.2 and the fire protection regulations, in
addition to the directives of the association of can-
tonal fire insurance companies, must be observed
without fail.
1.
The lateral spacing of the working surface cut-out
from a high-level cabinet and the rear wall must be
at least 50 mm.
2.
Cut out working surface according to specified
cut-out dimensions. The tolerances must be
observed.
3.
Holes for the built-in switchbox in the front of the
cabinet with template as illustrated.
Panel thickness min. 16 mm, max. 22 mm.
4.
Guide the built-in switchbox with the bundle of
connecting conductors from above through the
working surfaces cut-out and from the rear to the
front of the cabinet.
Warning:
There are capillary tubes in the bunch
of conductors between the built-in switchbox and
the grill plate. Do not bend sharply or separate or
the appliance will be destroyed!
5a.Assembly with CN-front panel (CN)
Guide the signal lamps from the rear through the
12 mm dia. holes in the front of the cabinet (the
12 mm dia. holes can be enlarged to 15 mm to
simplify assembly). Take the switch spindle(s) of
the built-in switchbox from the rear through the
13 mm dia. hole(s) and insert the signal lamps in
the signal lamp lenses mounted on the CN front
panel from the rear.
– TY58: insert signal lamp with red wires in the
left-hand red lens.
– TY38: insert signal lamp with red wires in
upper red lens.
Screw CN-front panel with screws to front of cabi-
net under switch knobs. Attach switch knobes and
then secure built-in switchbox in front of cabinet
from rear
5b.Assembly without CN-front panel (Vi)
Insert the signal lamp lenses supplied from the
front in the 12 mm dia. holes of the front of the
cabinet.
– TY58: left-hand red lens.
– TY38: upper red lens.
Insert the signal lamps from the rear through the
front of the cabinet in the signal lamp lenses.
– TY58: insert signal lamp with red wires in the
left-hand red lens.
– TY38: insert signal lamp with red wires in
upper red lens.
Take the switch spindle(s) of the built-in switchbox
from the rear through the 13 mm dia. hole(s),
attach white or black switch knobs as required and
then secure the built-in switchbox from the rear to
the front of the cabinet.
6.
Clean the working surface thoroughly in the cut-
out and in the rebate.
7.
The enclosed rubber tape (3x10x2400 mm) must
be attached to the cut-out supporting surface (to
soften blows and prevent silicone joint sealing
compound running under the grill plate under all
circumstances when pointing).
Warning:
If not fitted correctly, removal would be
made more difficult for servicing. The grill plate
and working surface could be damaged in this
way.
8.
Place grill plate carefully in cut-out and align so
that the joint is the same size on all sides, The grill
plate is not fastened!
Warning:
A recess base which can be dismantled
must be fitted as contact protection under the grill
plate/built-in switchbox.
9.
Clean grill plate and working surface in area of
joint (e.g. with isopropyl alcohol S-150 and fluff-
free cloth) and fill the joint with a heat-resistant (at
least 160 °C) silicone joint sealing compound (e.g.
Pactan 6076 anthracite).
Note: Since the grill plate and working surface cut-
out are subject to a certain dimensional tolerance,
the width of the joint can vary (min. 2 mm).
Removing the grill plate
1.
Remove power supply from built-in switchbox/grill
plate.
2.
Cut open the silicone joint sealing compound pro-
vided by the client with a suitable knife along the
edge of the grill plate to the full depth of the joint.
Raise the grill plate carefully from below to the
lower construction shell with a screwdriver.
3.
For a new fitting it must be ensured that the old sil-
icone compound and the rubber tape are cleanly
removed completely and a new rubber tape fitted
for softening blows (available from spare-parts
sales, 3x10x2400 mm). Re-fitting is performed
according to the fitting/installation text.
Removing the built-in switchbox (for servicing)
1.
Remove power supply from built-in switchbox and
dismantle the recess base.
2.
Pull off switch knobs (if present remove CN front
panel forwards). Withdraw signal lamps from the
lenses from the rear, release fixing screws of built-
in switchbox on the front of the cabinet from the
rear, draw the switchbox forwards carefully through
the opening in the recess base. Re-fitting is per-
formed according to the fitting/installation text.
Warning:
There are capillary tubes in the bunch of
conductors between the built-in switchbox and the
grill plate. Do not bend sharply or separate or the
appliance will be destroyed!
