Electrolux T5130 Скачать руководство пользователя страница 42

Страница: 42 / 94

Heating unit, electric

Connect the new element. Reconnect the wires as before, use the electric schematic supplied
with the machine.

Mount the element unit back in the machine and fasten the three screws under the machine.

Carefully put the drum package back in the machine.

Fasten the support rollers at the front of the machine.

Connect the RMC and the “FREE” connection if disconnected.

Connect the wires and mount the cover panel to the electrical connections.

Fasten the four screws at the panel around the heating element and the rest of the screws on
the panel.

Fasten the belt. Rotate the drum to make sure that the belt is in position.

Mount the air channel panel.

Connect the overheating thermostat and the heating sensor.

Mount the top panel, the cover panel at the air outlet and the casing over the rear panel.

T5130C

Disconnect the power to the machine.

Demount the casing over the rear panel.

Disconnect the overheating thermostat and the heating sensor and push the connections into the
hole.

fig.7519C

Содержание T5130































































































Результаты поиска

Содержание T5130

Отзывы:

Electrolux T5130, Руководство по обслуживанию, Страница: 42 / 94

Результаты поиска

Содержание T5130

Отзывы: