Electrolux EWM2000 Скачать руководство пользователя страница 47

Страница: 47 / 74

ALARM CODES

SSD-P APdV, EB, HD 01/05

8.29

599 34 71-47

YES

Washing NTC sensor failure.

(ohm value of the NTC out of limits)

Checks to do:

E71

Get inside diagnostic cycle and fill

in water on

step 5

to make the

pressure switch operating .Turn off

machine and on main board plug

measure between J4-1 and J4-2

an Ohm value (between 5.7 and

6.3 KOhm at 20

Do you read the Ohm value?

see pic .16

Unplug connectors.

Measure directly on

the NTC the Ohm

value. Do you read

the right Ohm value?

see pic. 27

Change the NTC

sensor and run again

the diagnostic cycle

to verify any further

possible alarm.

Measure between J4-1 and body

of the machine and between J4-2

and body of the machine. Do you

measure any dispersion?

see pic. 20 -

Change/Check the

cable and run again
the diagnostic cycle

to verify any further

possible alarm.

Unplug connector and measure

directly between NTC sensor

body of the machine . Do you

measure any dispersion? The

machine must have water inside.

see pic.31

Change the NTC sensor and run

again the diagnostic cycle to verify

any further possible alarm.

Change the Main

board and run again

the diagnostic cycle

to verify any further

possible alarm.

Change/Check the

cable and run again
the diagnostic cycle

to verify any further

possible alarm.

YES

If there are burn marks on
electronic board, see page 13.1-2

Содержание EWM2000











































































Результаты поиска

Содержание EWM2000

Отзывы:

Бренды по названию

Популярные бренды

Electrolux EWM2000, Руководство по обслуживанию

Результаты поиска

Содержание EWM2000

Отзывы:

Бренды по названию

Популярные бренды