Electrolux EWM2000 Скачать руководство пользователя страница 30

Страница: 30 / 74

ALARM CODES

SSD-P APdV, EB, HD 01/05

8.12

599 34 71-47

Pressure chamber blocked

The analogic pressure switch is not able to measure any variation of the water level

for at least 30-sec. during drum movement.

Checks to do:

Get inside the

diagnostic cycle and

go to

step 6

. Is the

motor turning and the

drum not moving?

YES

Empty the machine.

Verify the air trap

system and the

pressure switch

hoses. Is the system

free?

–

see pic. 08,a,b

YES

Clear \ clean the air

trap system and \ or

pressure switch

hoses and run again

the diagnostic cycle

E38

Refit \ change the

drive belt and run

again diagnostic cycle

to verify any further

possible alarm

Change the analogic

pressure switch and

run again the

diagnostic cycle to

verify any further

possible alarm

AC motor

: measure

between J1-7 and the

body of machine,

between J1-8 and the

body of machine,

DC motor

: measure

between J1-8 and the

body of machine,

between J1-9 and the

body of machine,

Do you measure any

dispersion?

YES

Change / check the

cable and verify any

further possible alarm

Содержание EWM2000











































































Результаты поиска

Содержание EWM2000

Отзывы:

Electrolux EWM2000, Руководство по обслуживанию, Страница: 30 / 74

Результаты поиска

Содержание EWM2000

Отзывы: