Electrolux EWM2000 Скачать руководство пользователя страница 35

Страница: 35 / 74

ALARM CODES

SSD-P APdV, EB, HD 01/05

8.17

599 34 71-47

YES

There is an incongruity on the component (Triac)

that commands the door lock device.

(1st page)

Checks to do:

E43

Unplug the connectors on

door lock and measure as

follow:

- Measure between

connector 3 and 5, you

should NOT find an open

circuit.

- Instead between connector

4 and 5, you should find an
OPEN circuit (numbers are

printed on the component).

Is the door lock OK?

3 Connections

–Traditional

or instant door lock device.

see pic 17,18

To verify the cable measure the

following connections on main

board plugs:

- Measure between wire on J2-3

and J7, you should NOT find an

open circuit

-Measure between wire on J2-1

and J2-3, you should find an

OPEN circuit.

-Measure between wire J2-1 and

wire going to connector 4 in the

door lock, you should find a short

circuit.

Is the system OK?

-see pic.

13,16,24

Change the door

lock and run the

diagnostic cycle

to measure any
further possible

alarm

Check/change the cables

and run again diagnostic

cycle to verify any further

possible alarm

Is the door

lock with 3 or

4 connectors?

4 Connections

(Instant door lock

device)

see next page (8.18)

Change the Electronic board and
run again the diagnostic cycle to
verify any further possible alarm.

If there are burn marks on
electronic board, see page 13.1-2

Содержание EWM2000











































































Результаты поиска

Содержание EWM2000

Отзывы:

Electrolux EWM2000, Руководство по обслуживанию, Страница: 35 / 74

Результаты поиска

Содержание EWM2000

Отзывы: