WARNING:
First read sections: SAFETY RULES,
SAFETY USAGE and SYMBOLS.
STARTING A COLD ENGINE
1)
Position the on/off switch to the
I
(ON)
position, away from the «STOP» position.
2)
Rotate the choke lever in the direction illustrated
by the arrows. This engages the fast idle system.
3)
Squeeze the primer bulb (
C
) several times
until you see fuel begin to return back through
the tube (
D
) towards the fuel tank. Push the
decompression valve (
B
) down if your models
is fitted with one. Pull the starter handle until
the engine starts.
4)
Hold the machine safely and allow the engine
to run for a few seconds. Grip the control han-
dle firmly, pushing down on the safety trigger
(
S
) and then squeezing the accelerator trigger
(
A
). This action automatically releases the
spring loaded choke lever (
E
) disengaging the
fast idle system.
WARNING:
The fast idle system does cause the
cutting attachment to rotate when engaged.
STARTING A WARM ENGINE
Position the on/off switch to the
I
(ON) position.
Squeeze the primer bulb (
C
) several times until
you see fuel begin to return back through tube
(
D
) to the fuel tank. Pull the starter handle until
the engine runs.
HOT ENGINE STARTING WITH
1)
STOP switch on START position
I
. Trigger on
ENGLISH - 5
F. Blade and nylon string head assembly
G. Handle assembly
H. Starting and stopping the engine
Assemble the correct guard to suit the kind of
blade or nylon string head to be used (See sec-
tion: SAFETY GUARD ASSEMBLY).
1)
Assemble blade as illustrated:
a) Flange guard - b) Upper cap with blade
centering - c) Blade with text and directional
arrow facing upwards - d) Lower washer - e)
Fixed mower gauge - f) Blade locking screw
(length mm 16).
2)
If you want to assemble the rotating mower
gauge,proceed as illustrated:
a) Flange guard - b) Upper cap with blade
centering - c) Blade with text and directional
arrow facing upwards - d) Lower washer - e)
Spacer - f) Rotating mower gauge - g) Blade
locking screw (length mm 34,5).
Replace the blade attachment bolt if damaged
in any way.
3)
Make sure that the blade bore opening fits per-
fectly around the centering collar on the upper
cap.
Tighten counterclockwise.
While tightening, the blade assembly can be
held fast by inserting the wrench or the screw-
driver supplied into the cap and gearcase
holes.
To do this, rotate the cap intil the two holes
coincide.
4)
Assemble nylon string head as illustrated:
a) Flange guard - b) Upper cap - c) Guard d)
Nylon string head
Tighten counterclockwise.
5)
While tightening, the head assembly can be
held fast by inserting the wrench or the screw-
driver supplied into the holes as already shown
for blade assembly.
WARNING: Do not use the guard for the nylon
string head (18) when using a metal blade.
1) DOUBLE HANDLE
Handle (
A
) can be adjusted for individual
operator comfort by swivelling it forwards or
backwards. To do this, loosen button (
C
),
position the handle for maximum comfort,
then tighten button (
C
) securely. Clip the
suspension harness hook into one of the
holes on the top side of the shaft support to
achieve the best balance according to the
type of work to be undertaken.
NB:
Handle assembly (
A
) can be folded
parallel to the shaft to facilitate
transportation or storage. To do this,
loosen knob (
C
), twist support (
B
) 90° in a
clockwise direction, fold the handle (
A
)
into the required position and then tighten
knob (
C
).
2) DOUBLE HANDLE
Adjust and secure double hand clamp by tight-
ening the screws.
