8
7
Working with the blender
The appliance can be used for up to 1 minute without
stopping. It should be allowed to cool afterwards for at
least 1 minute.
Important: Blades are very sharp, handle with
care. Ensure that the hand-held blender is
unplugged from the power outlet before
assembling or removing attachments.
Insert the blender deep into the bowl, then press switch A
(for speed I) or switch B (for speed II) (Figure 2).
Start all types of processing at speed I. This will avoid
powdery foods and liquids spraying out.
Light upward and downward movements of the blender
permit the material being worked on to be handled in the
best possible way. Please make sure that:
–
the mixing attachment never has more than two-thirds
of its length immersed in the material,
–
the mixing bowl is never more than two-thirds full (to
avoid the danger of splashes).
Working with the chopper
(ZSTM310)
Figure 4.
Max operation duration under high speed per time
cannot exceed 1 minute, and 1 minute rest time must be
maintained at two consecutive cycles.
Place the chopper bowl on a clean, level surface.
Assemble the stainless steel blade into the chopper
bowl, as shown in position A.
Place food into the chopper bowl.
Note: remove the bone of the meat, cut small
piece (approximately 10-15 mm), then place the
meat into the bowl, the max quantity of meat
can
’
t exceed 200g in every blending.
Attach the lid onto the chopper bowl and turn it in
clockwise direction until it locks into position (see
position B).To detach the lid, turn in adverse direction.
Insert the top part of the chopper into the hole of the
chopper lid, and turn in clockwise direction to lock (see
position C).
Plug the appliance to power outlet and depress the
switch to begin operation.
To stop the appliance, release the switch at the top of the
motor unit.
Caution: To reduce the risk of injury, never place
cutting blade on base without first putting bowl
properly in place.
Be sure chopper lid is securely locked in place before
operating appliance.
Working with the egg white
beater (ZSTM310) Figure 5.
Max operation duration under high speed per time
cannot exceed 1 minute, and 1 minute rest time must be
maintained at two consecutive cycles.
To assemble the egg white beater with the motor unit,
turn the motor unit clockwise direction until tightened.
To disassemble, turn in the adverse direction (see
position A).
Plug the hand-held blender to power outlet.
Place egg white into the cup, generally, put two egg
white is enough (see position B).
Lower the hand-held blender into food and depress the
switch at the top of the motor unit (see position C).
To stop the hand-held blender release the switch at the
top of the motor unit.
Fixing wall bracket (ZSTM310)
Figure 6.
You can fix the wall bracket as following:
Drill two same holes in wall and strictly follow the
dimension as indicated.
Knock two plastic tubes in them with hammer.
Secure the bracket on wall with another two screws.
English
8
Cleaning and maintenance
Ensure that the hand-held blender is unplugged
from the power outlet before assembling or
removing attachments for cleaning or
maintaining.
Note: Do not immerse the detachable stem of the blender
in water because overtime the lubrication on the bearings
may wash away.
Wash the detachable stem under running water, without
the use of abrasive cleaner or detergents. After finishing
cleaning the detachable stem, place it upright so that any
water which may have got in, can drain out.
Wash the cup, bowl, beater and blade in warm soapy
water.
The mixing attachment, the bowl and the beater
are not recommended to place in dishwashing
machine as the plastic component deteriorate
through prolonged use of dishwasher cleaning.
Unplug the motor unit. Wipe the motor unit with a damp
cloth. Never immerse it in water for cleaning as an electric
shock may occur.
Dry thoroughly.
Caution: Blades are very sharp, handle with care.
Reassemble the blender shaft to motor unit then place it
upright in wall bracket (see Figure 6.) or hang it up for
saving space.
Quick cleaning
Between processing tasks, hold the hand-held blender in
the cup half filled with water and turn on for a few seconds.
Technical data
Mains voltage:
230 V, 50 Hz
Power consumption:
400 W
Maximum continuous operating time:
1 minute
; This appliance conforms with the following EC Directives:
•
Low Voltage Directive 2006/95/EC
•
EMC Directive 89/336/EEC with amendments 92/31/EEC
and 93/68/EEC
Disposal
Packaging material
The packaging materials are environmentally friendly
and can be recycled. The plastic components are
identified by markings, e.g. >PE<, >PS<, etc. Please
dispose of the packaging materials in the appropriate
container at the community waste disposal facilities.
Old appliance
The symbol
on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical
and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential
negative consequences for the environment and human
health, which could otherwise be caused by
inappropriate waste handling of this product. For more
detailed information about recycling of this product,
please contact your local city office, your household
waste disposal service or the shop where you purchased
the product.
English
(STM1255)
(STM1255)
(STM1255)
ELX13669_IFU_Stickmixer_AEG_3lang_insert.indd 8
2010-07-01 11:21:32
