Electrolux Professional W4 H Series Скачать руководство пользователя | Manualshive

Страница: 21 / 40

background image

Installation manual

21

5 Water connection

All water intake connections to the machine should be fitted with manual shut-off valves and filters, to facilitate instal-
lation and servicing.
Water pipes and hoses should be flushed clean before installation.
The machine shall be connected with new water hoses. Re-used water hoses must not be used.
Hoses are to be of an approved type and grade and comply with IEC 61770.
The hoses should be rated for high pressure and for 2.5 MPa
After installation hoses must hang in gentle arcs. (This is particularly important if the machine is fitted with a tilting
function). Connections with pipes directly to the machine is not allowed.
Connect the water:

• Cold water (A)
• Hot water (B)
• Third water (C)
Connection size (W4400H, W4600H): DN 25 (1" BSP).
Connection size (W4850H, W41100H): DN 32 (1 1/4" BSP).

A

B

C

fig.5869A

Water pressure:
Continuous operating pressure: 50–800 kPa (0.5-80 kp/cm

2

)

Maximum: 1000 kPa (10 kp/cm

2

)

Recommended: 200–600 kPa (2–6 kp/cm

2

)

Note!

If the water pressure is below the minimum value, the wash result can not be guaranteed for certain program.

FOR AUSTRALIA:
The appliance shall be installed in accordance with AS / NZS 3500.1
The appliance need to be installed using dual check valves.
Contact details for after sales service: [email protected]

«
...
19
20
21
22
23
...
»

Содержание W4 H Series









































Отзывы:

Нет отзывов

Похожие инструкции для W4 H Series

BD 70/75 W Classic Bp Pack 160 Ah Li + FC

Бренд: Kärcher Страницы: 48

Бренд: Pacific Страницы: 12

Бренд: bora Страницы: 32

Бренд: IPC Страницы: 2

Бренд: S&P Страницы: 3

Бренд: YANGZI Страницы: 18

Minuteman RoboScrub 20

Бренд: HAKO Страницы: 150

Бренд: Kärcher Страницы: 12

Бренд: COMAC Страницы: 3

Бренд: Ocean Matrix Страницы: 2

Бренд: Toolson PRO Страницы: 100

Бренд: LYSON Страницы: 6

Бренд: LYSON Страницы: 17

Бренд: Fumex Страницы: 20

LINEAR CENTRALE

Бренд: ROBLIN Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды