Electrolux Professional W4 H Series Скачать руководство пользователя | Manualshive

Страница: 15 / 40

background image

Installation manual

15

Lift the machine and remove pallet and blocks.

fig.5548

The feet can be of two types: fixed feet or rotating feet if the machine is to be fitted with tilt or weighing equipment.
For machines with tilt or weighing equipment: screw on the machine’s feet.

Note!

If the machine is to have the tilt function, this is a suitable time to install the corner posts which hold the pro-
tective plates, and also, where applicable, the position sensors. (For more information please refer to sec-
tion “Installation of machines with tilt function”).

It is important that the wheels are installed with the wider side facing in towards the machine (D) in order for the tilt
protection to fit.

D

fig.7223A

Note!

When moving the machine, handle it with care.

Place the machine on its final position.

«
...
13
14
15
16
17
...
»

Содержание W4 H Series









































Отзывы:

Нет отзывов

Похожие инструкции для W4 H Series

Бренд: S&P Страницы: 40

Бренд: Tornado Страницы: 13

i-synergy I20NBT-LA

Бренд: Ice Страницы: 49

Бренд: Minuteman Страницы: 91

Бренд: lavina Страницы: 13

Бренд: Lamona Страницы: 15

HYDRO-FORCE MX1200M

Бренд: Nautilus Страницы: 93

Бренд: COMAC Страницы: 24

Бренд: FAIE Страницы: 3

Бренд: YANGZI Страницы: 12

SPEED SCRUB 500

Бренд: Nobles Страницы: 44

Comanche 10075270

Бренд: Prochem Страницы: 15

Бренд: Prochem Страницы: 29

Ninja Warrior 500 PSI 10070680

Бренд: Prochem Страницы: 52

Ninja Warrior 200 PSI 10070650

Бренд: Prochem Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды