ElectroCraft CompletePower Plus CPP-A12V80A-SA-USB Скачать руководство пользователя | Manualshive

Страница: 9 / 42

background image

© ElectroCraft 2018

8

CPP-A12V80A-SA-USB Technical Reference

14. Do not make any extreme adjustments or settings changes of parameters. Failure to observe this

caution may result in injury due to unstable operation.

15. Avoid plugging connector J1 into the drive while live power is applied to the connecting cables.

Ignoring this precaution will cause electrical arcing at the connector pins, which can cause

permanent connector damage. ElectroCraft recommends using a disconnect switch ahead of J1 if

the drive must be disconnected often.

16. Do not remove the connectors on ports J1 through J6 from the drive while the motor is operating.

17. Do not service or modify this product. Only authorized personnel must perform disassembly or

repair of the drive. Failure to observe warning may result in injury or damage to product.

18. Always operate the drive within the prescribed voltage limits. Any attempt to operate outside

these bounds may result in damage to the drive.

19. Safe use of this product depends on factors specific to the end application. These factors are

outside of ElectroCraft knowledge and control. The installer of this servo drive must have a

thorough knowledge of safety precautions and practices relevant to the specific application of this

drive. In particular the installer should consider the risks associated with erroneous or non-

operation of the servo drive in the application and mitigate them appropriately.

1.2 Storage and Transportation

1. Do not store or install the product in the following places:

a. Locations subject to temperature outside of the range specified.

b. Locations subject to humidity outside the range specified.

c. Locations subject to condensation as the result of changes in temperature.

d. Locations subject to corrosive or flammable gases and liquids.

e. Locations subject to dust, salts, or electrically conductive contaminants.

f. Locations subject to exposure to water, oil, or chemicals.

g. Locations subject to shock or vibration.

Failure to observe this caution may result in fire, electric shock, or damage to the product.

2. Do not hold the product by the cables or motor shaft while transporting it. Failure to observe this

caution may result in injury or malfunction.

1.3 Environmental Protection

Waste electrical products should not be disposed of with household waste. Please recycle where facilities

exist. Check with your Local Authority or retailer for recycling.

«
...
7
8
9
10
11
...
»

Содержание CompletePower Plus CPP-A12V80A-SA-USB











































Отзывы:

Нет отзывов

Похожие инструкции для CompletePower Plus CPP-A12V80A-SA-USB

Бренд: BAREL Страницы: 8

Бренд: Brasiltec Страницы: 75

YSLO FLEX RTS 1P

Бренд: SOMFY Страницы: 28

Бренд: YASKAWA Страницы: 284

Бренд: FujiFilm Страницы: 252

Automation1 iXL2e

Бренд: Aerotech Страницы: 96

Бренд: Tridonic Страницы: 12

Бренд: Panasonic Страницы: 20

MINAS A4-series

Бренд: Panasonic Страницы: 26

Бренд: Panasonic Страницы: 27

Бренд: Panasonic Страницы: 35

Бренд: Panasonic Страницы: 58

Бренд: Panasonic Страницы: 85

Бренд: Panasonic Страницы: 111

Бренд: Panasonic Страницы: 115

MINAS A6N Series

Бренд: Panasonic Страницы: 495

HF-430NEO Series

Бренд: Sumitomo Страницы: 25

Бренд: hager Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды