ElectroCraft CompletePower Plus CPP-A12V80A-SA-USB Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 42

background image

© ElectroCraft 2018

28

CPP-A12V80A-SA-USB Technical Reference

7.4 Motor Temperature Sensor

A motor over-temperature protection function is provided by the drive. The drive is designed to be

compatible with standard Electrocraft motors equipped with a thermistor temperature sensor. However

the drive is capable of interfacing with any resistance based temperature sensor that meets the following

criteria.

•

The resistance of the temperature sensor decreases with increasing temperature.

•

The resistance at the maximum motor temperature is 1k

Ω

(typical).

•

The sensor is isolated from any voltage sources (the drive provides the necessary excitation)

This sensor is commonly a thermistor or a normally open temperature switch that closes at the desired

shutdown temperature. If motor over temperature function is not used, the connections must be left open.

Contact the factory for applications with temperature sensors that do not match these specifications.

7.4.1 Temperature Sensor Connections

Temp Sensor
Temp Sensor

Motor

J3

Drive

J3

Figure 19: Temperature sensor connection to the drive

7.4.2 Temperature Sensor Signal Input Circuit

Motor

Temperature

Input

+5V

100

KΩ

+

_

100

KΩ

4700pF

100

KΩ

100

KΩ

1

KΩ

+5V

1uF

680

Ω

Figure 20: Temperature sensor signal input circuit

«
...
27
28
29
30
31
...
»

Содержание CompletePower Plus CPP-A12V80A-SA-USB











































Отзывы:

Нет отзывов

Похожие инструкции для CompletePower Plus CPP-A12V80A-SA-USB

Бренд: TOYODenki Страницы: 64

Бренд: Parker Страницы: 54

Бренд: Creator Страницы: 2

Бренд: BLUM Страницы: 28

Бренд: RIB Страницы: 44

Бренд: YASKAWA Страницы: 138

Бренд: GSK Страницы: 79

Бренд: GSK Страницы: 105

Бренд: FujiFilm Страницы: 547

Бренд: HAUTAU Страницы: 8

Бренд: D+H Страницы: 10

OPTIONS Zip 100MB IDE

Бренд: IBM Страницы: 52

Бренд: Idex Страницы: 28

Бренд: Parker Страницы: 62

Бренд: Eaton Страницы: 16

Бренд: Bosch Страницы: 40

Water Drive Series

Бренд: HIDROCONTROL Страницы: 25

Бренд: Bholanath Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды