ElectroCraft CompletePower Plus CPP-A12V80A-SA-USB Скачать руководство пользователя страница 20

Страница: 20 / 42

CPP-A12V80A-SA-USB Technical Reference

3.3.9 Analog Output

Parameter

Conditions

Min.

Typical

Max.

Units

Output Voltage

Operational range

-10

Load impedance

Connected to ground

3.3.10 USB Communications

Parameter

Conditions

Type

USB on the drive

USB mini type B female

USB 2.0 compatible communications

interface

3.4 De-rating

The drive is protected against overheating. The protection mechanism employed is to shut off current to

the motor when the drive internal temperature reaches the maximum limit. The thermal performance of

the drive is dependent on the application and the environmental conditions. This section provides

guidance for application of the drive within the recommended operating conditions referenced in this

manual. However, thermal performance of the drive is dependent on the specifics of the application and

the environmental conditions.

The drive does not have any temperature or output PWM frequency derating in the ambient temperature

range of 0 to 40°C when mounted according to ElectroCraft recommendations as specified in section 4.1.

Operating the drive outside ElectroCraft recommendations or in a closed box and stagnant air may limit

maximum performance. Use of additional heatsinking or forced air may be required. For applications

outside ElectroCraft recommendations or in ambient temperature outside the limit of 0 to 40°C, please

contact ElectroCraft.

Содержание CompletePower Plus CPP-A12V80A-SA-USB











































Результаты поиска

Содержание CompletePower Plus CPP-A12V80A-SA-USB

Отзывы:

Похожие инструкции для CompletePower Plus CPP-A12V80A-SA-USB

Бренды по названию

Популярные бренды

ElectroCraft CompletePower Plus CPP-A12V80A-SA-USB, Техническое описание

Результаты поиска

Содержание CompletePower Plus CPP-A12V80A-SA-USB

Отзывы:

Похожие инструкции для CompletePower Plus CPP-A12V80A-SA-USB

Бренды по названию

Популярные бренды