3.3 Bodypack Trans mit ter REV-BP
A. In stall An tenna.
The REV-BP is equipped with a de tach -
able an
tenna. Screw in the an
tenna in
cluded with the
sys tem. See the ac ces so ries sec tion at the end of this
man ual for op tional an ten nas.
B. In sert Bat ter ies.
Pinch the bat tery door tabs in ward and
pull the door open. In sert a 9V bat tery as in di cated by +/-
in the holder. (Note: the REV-BP unique de
sign al
lows
the bat tery to be in serted and used re gard less of the pos -
i tive and neg a tive ter mi nal po si tion, the in di ca tors are
there for ref er ence only).
C. Turn ing the trans mit ter On -
With bat tery com part ment
still open, turn the unit on with Power switch on the top
panel. The bat
tery low LED and dis
play back light will
light for a sec ond and the dis play will show the bat tery
level, the Group and Chan nel num bers.
D. Change the group and chan nel num bers
1. Press SET, the Group num ber will flash and can be
changed with the UP/DOWN keys.
2. Once the de
sired Group num
ber is show
ing, press
SET to se lect and the Chan nel num ber will flash.
3. Se lect the Chan nel and press SET again, the flash ing
will stop and the chan nel is now set.
E. To See Other Screens
1. Press SET and DOWN at the same time to dis
play
the ex act trans mit fre quency.
2. Press SET and DOWN at the same time to dis
play
the bat tery level in per cent.
3. Press SET and DOWN again to dis play the gain set -
ting screen.
4. Press SET and DOWN again to show the RF Trans -
mit Level.
5. Press SET and DOWN again for Voice/Gui tar.
6. Set and Down one more time re
turns you to the
Group and Chan nel screen.
F. Fre quency Edit Mode - (User Group Only)
1. With the fre quency screen dis played, press SET and
use UP and DOWN to ad just fre quency.
2. Press SET and DOWN at the same time four times to
re turn to Group and Chan nel mode.
G. At tach Mi cro phone or Gui tar/In stru ment
Mi cro phone
- plug the TA4 end of the mi cro phone ca ble
into the top panel of the REV-BP. Speak into the mi cro -
phone and the Au dio Me ter bar graph should in di cate au -
dio sig nal pres ence.
Gui tar -
Press SET-DOWN un til voice is dis played. Press
SET, dis play will flash, press UP and dis play will change to
Gui
tar, press set and re
turn to main dis
play.
NOTE:
The
REV re ceiver must also be put into in stru ment mode to op -
ti mize the sys tem for gui tar. Plug in the gui tar TA4 ca ble.
Strum the gui tar and the Au dio Me ter bar graph on the re -
ceiver should in di cate au dio sig nal pres ence.
H. Gain Set ting Mode
1. With the Gain Screen dis played, press SET and the
level num bers will flash.
2. Use UP and DOWN to ad
just the trans
mit
ter gain.
Watch the Au
dio me ter on the re ceiver and set the
gain to peak be
tween 50 and 100 when sing
-
ing/speak ing into the mi cro phone as loud as it will be
used dur ing the per for mance.
3. Press SET and DOWN at the same time two times to
re turn to Group and Chan nel mode.
NOTE:
Op er at ing with the trans mit ter au dio gain set as high
as pos
si
ble (with
out dis
tor
tion or peaks all the way to the
right end of the me ter) will re sult in the best per for mance and
high est sig nal to noise ra tio.
I. RF Trans mit Level
1. With the RF Trans mit Level dis played, press SET and
the Level (on the right) will flash.
2. Use UP and DOWN to set it at Hi (50 MW) or Lo (5mW).
3. Press SET and DOWN at the same time once to re -
turn to the Group and Chan nel mode.
J. Power Lock Out - Dis ables the power switch
1. To en
gage power lock press and hold SET, UP and
DOWN at the same time un til ON-LOCK ap pears in the
dis play.
2. To turn the unit off while in ON-LOCK, place the
power switch in the OFF po si tion and push any one of
the SET, UP or DOWN but tons.
3. To re
move the lock, press and hold SET, UP and
DOWN again at the same time un til ON-OFF ap pears
in the dis play.
4. The ON-LOCK mode can also be en tered by quickly
cy cling the power switch three times. But us ing this
method the unit will not be in ON-LOCK the next time
it is pow ered up.
K. Change Lock-Out - Dis ables the SET but ton to
pro tect set tings.
1. To en gage Change Lock press and hold the UP and
DOWN ar row keys to gether un til SE CURE ap pears in
the dis play.
2. To re
move the Change Lock, press and hold the UP
and DOWN keys un til AC CESS ap pears in the dis play.
L. Ver ify re cep tion
1. With the trans
mit
ter and re
ceiver on and match
ing
Group and Chan nel, the main re ceiver dis play should
be in di cat ing an RF sig nal on the bar graph.
2. Speak into the mi cro phone and the Au dio Me ter bar
graph should in di cate au dio sig nal pres ence.
3. If the level me ters do not show re cep tion, make cer -
tain the group and chan nel are match ing and re fer to
the trou ble shoot ing sec tion.
4. Go back to Sec tion 3.1 - Re ceiver Setup & Op er a tion
Step 1) to com plete sys tem set up and test.
-13-
