background image

B

OILER

 A

CCESSORIES

B

OILER

 A

CCESSORIES

This will simplify your wiring and make zoning applications much easier.  In addition, enhanced communicating 
features have the ability to stage the electric boiler based upon the connected zone capacity.

Standard Features

 • 

Utility load control

  •  Terminal block wiring, visual 

wiring layout

  •  Indicator lights showing zone 

operation

 • 24-volt, 

40VA 

transformer

  120/208/240 

connection

 • Fuse 

protection

 • Priority 

option

  •  Dual temperature operation

  •  Applies to digital or

  standard 

thermostats

  •  Dial switch, select each zone 

capacity

Pumps, Actuators, Valves

  EB-ZTA-1 - install within boiler cabinet
  EB-ZEA-1 - with enclosure and 40VA transformer
  EB-ZEA-2 - add additional 4, enclosure and 40VA

Pumps

  EB-Z2P - two pumps with priority and dual temp.

Zone Valves

  EB-ZTS-1 - install within boiler cabinet, encl. option
  EB-ZTS-2 - add additional 4, enclosure and 40VA

All Others

  EB-ZXA-1 - universal, pumps or valves, non-communicating, for any boiler
  EB-ZS-4 - automatic staging system for Brand X boilers or dual EB-R, -L, -E Series
  EB-ZC-4 - wiring and convenience interface, isolated boiler end switch
  EB-5415A - low cost, 2 or 3 zones, sheds one boiler stage (Mini-Boiler enhancement)

ZONE CONTROLLER

SLAB STAT

Sensing and controlling the system based upon radiant fl oor surface temperature 
or the concrete mass has very positive benefi ts.  Radiant fl oor air stat in the same 
area as a forced air roomstat presents serious control problems.  A remote sensing 
slab stat for the radiant fl oor removes this issue.

Remote sensing slab stat is required for storage applications.

ES-24-BR

SWITCHING RELAY - EE-5051 

MULTI-BOILER - EB-C-STG5

This DPDT 24-volt switching relay provides a convenient 
solution to any AC or DC application.

• 

Ideal for zone pumps

• 

24V coil

• 

120V, 10A, contact sets

• 

Easy to wire and nicely packaged

Electrically connects between 2

nd

 and 3

rd

, 3

rd

 and 4

th

, etc.

 OTHER 

OPTIONS

SOT-1 

Switchover to standby, total run time

5701 

Single feed bus for 2 CB’s (SQ-D CB)

5702 

Single feed bus for 3 CB’s (SQ-D CB)

EB-S-SB 

Dual boiler option for EB-S Series

WF-ANZ*  WarmFlo Analyzer, now applicable to WO and 

WA Series

Specifi cations subject to change without notice, all rights reserved.

Содержание EB-MO-10



























Отзывы: