background image

10/22/2008 

4

 BI510 

 
 
MULTIPLE BOILERS 

 

This boiler series now includes a method for automatically staging any 
number of parallel-plumbed boilers.  Order plug-in relay EB-C-STG5. 

 

The thermostat is connected only to the first boiler, when all stages are 
on for more than 5 minutes, this new plug-in relay module turns on the 
next boiler (R and W), and a second EB-C-STG5 could be used to turn 
on the third, etc. 

 
 
 
BOILER/PLUMBING KIT PLACEMENT 

 

This model series is wall hung and the vessel must be vertical, drawing BX505. 

 

The plumbing kit items are located adjacent to the boiler housing itself as shown on drawing BX501 or 
BX505. 

 

For future servicing, the unit itself must be installed 20” or more above the floor, the elements are 
screwed in from the bottom. 
 

INFORMATION/WATER FLOW CALCULATIONS

 

 
Water flow, GPM, can easily be calculated if the temperature rise across the electric boiler can be 
measured. 
 
The formula below can only be used when the temperature rise is stable and the boiler is not hi-limiting.  
In other words, verify constant current draw and stable outlet temperatures for at least 15 minutes. 
 
 

GPM = Volts x Amps x 3.4 

 

 

        500 x Temp. rise 

 

INSTALLATION REQUIREMENTS

 

 
1.

 

All installation work must be performed by trained, qualified contractors or technicians.  Electro 
Industries, Inc., sponsors installation and service schools to assist the installer.  

Visit our web site at 

electromn.com for upcoming service schools.

 

 

 

WARNING

 

ALL ELECTRICAL WIRING MUST BE IN ACCORDANCE WITH NATIONAL ELECTRIC CODE 
AND LOCAL ELECTRIC CODES, ORDINANCES, AND REGULATIONS. 

 

 

WARNING

 

OBSERVE ELECTRIC POLARITY AND WIRING COLORS.  FAILURE TO OBSERVE COULD 
CAUSE ELECTRIC SHOCK AND/OR DAMAGE TO THE EQUIPMENT. 

 

 

CAUTION

 

This unit can only be used for its intended design as described in this manual.  Any internal 
wiring changes, modifications to the circuit board, modifications or bypass of any controls, or 
installation practices not according to the details of this manual will void the product warranty, 
the CSA/us certification label, and manufacturer product liability.  Electro Industries, Inc., 
cannot be held responsible for field modifications, incorrect installations, and conditions which 
may bypass or compromise the built-in safety features and controls.

 

Содержание EB-MO-10



























Отзывы: