Electro-Harmonix OCEANS 12 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 40

Electro-Harmonix OCEANS 12 Скачать руководство пользователя страница 15

15

- SEND/RETURN FX LOOP -

The Oceans 12 has the ability to create a special, wet, mono FX LOOP

either before or after the reverb block. See the following diagram:

The SEND is output through the R/SEND OUT jack. The return is

connected to the R/RETURN IN jack.

Tip: useful for

when you’d like a

n

effect in your chain, for example a fuzz or filter, to affect only the reverb

tails, i.e. without affecting your dry signal.

The amount of signal routed to the SEND path is controlled by the SEND

LVL, the alternate parameter of the PREDELAY knob. This knob controls
the SEND LVL whenever FUNCTION is on. (See page 13 for details on

the FUNCTION button). When the knob is turned fully counter-
clockwise, the SEND LVL is zero. The SEND LVL increases as the knob is
turned clockwise, reaching unity when fully clockwise.

Note: the default

value of the SEND LVL is zero. When a SEND/RETURN configuration is

active, be sure to adjust the SEND LVL to your desired amount.

The status of the Send/Return FX loop is always either

pre-reverb,

post-

reverb,

or

OFF

(i.e., regular stereo operation)

.

If the status is either

pre-

reverb

or

post-reverb

, the green S/R LED on the bottom-left of the unit

(pictured below) will be lit after the pedal is powered up. The Oceans

12 will remember the FX loop status, even after removing power.

«
...
13
14
15
16
17
...
»

Содержание OCEANS 12









































Отзывы:

Нет отзывов