UM90696E 01.07.2016 GB
1. Keep the PROG button pressed for approx
5 seconds. The PROG button will flash slowly
and you will hear an acknowledgement signal.
2. Press the PROG and mode button at the same
time. You will hear an intermittent signal tone
and both buttons will flash quickly.
3. Press the transmission button of the trans-
mission code you would like to delete until a
brief acknowledgement signal is played and
both buttons light up. The transmission code
has been deleted and the device will auto-
matically switch back to operational mode.
Attention!
With a RESET all memorized
transmission codes as well as all relevant settings
are deleted and factory settings are activated.
1. Press the programming button of the radio bell
(approx. 5 seconds). The programming button
will flash slowly and the device will play an
acknowledgement signal.
2. Press the PROG and mode button at the same
time. You will hear an intermittent signal tone
and both buttons will flash quickly.
3. Press the PROG and loudspeaker button until
a brief acknowledgement signal is played and
both buttons light up. and the radio gong will
switch back to its default settings.
Delete Transmission Code
Reset to Default Settings
> 5 s
approx.1,6 s
> 5 s
> 1,6 s
> 1,6 s
1. Briefly (< 1.6 seconds) press the mode button.
The march melody will play.
2. Press the loudspeaker button several times
while the ring tone is being played. The device
will switch to the next volume/flashlight option.
If you do not press the loudspeaker button,
kombination of volume and flashlight will be
accepted automatically after ring tone melody
has stopped playing.
Changing Ring Tone Volume /
Switching Flashlight On and Off
Disposal
Conformity
Customer Service
Put the packaging material into the
recycling bins for cardboard, paper and
plastics.
Dispose of the waste product via a collec-
tion point for electronic scrap or via your
specialist dealer.
Waste electrical products should not be
disposed of with household waste!
The product fulfils the essential require-
ments of the R&TTE directive
1999/5/EG.
Warranty
We will remedy defects on the device based on
material or production errors within the statutory
warranty period or exchange the device.
Any unauthorized tampering with, or modifica-
tions to, the product shall render this warranty null
and void.
For application in: EU/CH/FL/IS/N
The Declaration of Conformity can be found on
the internet at: www.eldat.de
General Information
If the device does not work properly despite
proper handing or in case of damage, please
contact your retailer or the manufacturer:
ELDAT GmbH
Im Gewerbepark 14
15711 Königs Wusterhausen
Germany
Phone:
+ 49 (0) 33 75 / 90 37-310
Fax:
+ 49 (0) 33 75 / 90 37-90
Internet: www.eldat.de
E-Mail:
Frequency:
868.30 MHz
Modulation:
FSK
Radio channels:
1
Range:
up to 150 m under
favourable open field
conditions
Opperating voltage:
230 V AC / 50 Hz
Current consumption: max. 7 mA
Power consumption: 0,3 W Stand by
Gong volumes:
Distance 30 cm:
quiet: 75 dB
loud: 82 dB
Protective type:
IP 20
Operating
temperature:
-20°C to +35°C
Max. relative air
humidity:
60%
Mains output:
Power plug
non switchable
Max. contact load:
D(A/NL/S/N) Schuko 10 A / 230 V AC
CH
10 A / 230 V AC
Dimensions
(HxWxD)
122 x 50 x 38,3 mm
Weight:
approx. 190 g
Technical Details
Loud +
flashing
light
Mute
Quiet
(no flashing
light)
Loud (no
flashing
light)
Quiet +
flashing
light
< 1,6 s
Press the
loadspeaker
button until the
desired
combination is
played.
PROG
PROG
To cancel press the loudspeaker button
To cancel press the loudspeaker button
PROG
PROG
PROG
PROG
PROG
