ELCOS CIM-130-KLRV Скачать руководство пользователя страница 17

 

 

Valid for firmware revision 1.00 and above

 

CIM-130&136-KLRV             MAN - EN – p.

 

17 of 16

 

Other types of SMS will not be accepted. 

 

RESET

 

Possibility to restore all the intervened protection devices  and the general alarm. 

To restore all the protections 
of the engine of the pump, key in 

RESET on the mobile phone. 

Reply message from control unit to mobile phone: 
“reset command carried out” 

 

 

POSSIBILITY TO COMMAND 

STARTING, ACCELERATION, DECELERATION AND STOPPING

 

It is possible to carry out the commands of all the mobile phones programmed in the control unit by keying in the code 

on the mobile. Before beginning the starting process, a buzzer is activated for 8 seconds, and after a 3-second pause the 

starting process begins.. 

The code  

 

START or the code 008 or ON 

After the START command 

the screen displays:  

 

 

Reply message from control 

unit to mobile phone: 

 

 

The motor pump  

has started. 

 

 

 

The code 

 

STOP or the code 005 or OFF

 

After the STOP command,  

the screen display:  

 

Reply message from control 

unit to mobile phone: 

 

The motor pump  

has stopped. 

 

FUEL FAULT

 

The fuel fault depends on any change in the fuel level in the motor pump tank when the engine is stopped. The check-
up is enabled after receiving the text message “PROT ON” (or “040”) and after the engine has been switched off for 5 
minutes. A negative change in the fuel level generates the fault which is signalled by the activation of the alarm output 
and the sending of a “FUEL FAULT” text message. The fault is triggered if the percentage drops by 10% when the level is 
between 100% and 80%, whereas it must drop by 5% if the level is between 79% and 1%. The fault is delayed by 5 
seconds and is stored. The fault threshold is updated by resetting the fault itself and after 5 minutes are up. When the 
tank is topped up, the threshold is automatically updated. A further text message (“OFF Status”) is sent when the 
operator switches the control unit OFF. 
 

The check-up is disabled by sending the text message “PROT OFF” (or “041”) or by disconnecting the battery supply from 

the control unit.

 

WATER PRESSURE 

HOUR OF OPERATION 

MOTOPOMPA 

Содержание CIM-130-KLRV





















Отзывы: