All disclosures, notices and warranty conditions are being written on the EKWB website. Please read terms of use. Released on 24
th
of July, 2015. Revision 1.0
Installation and mounting manual for EK-FC980 GTX Ti WF3 water
block
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability
whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at
installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.
Before you start using this product please follow these basic guidelines:
1.
Please carefully read the manual before through before beginning with the installation process!
2.
Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages t o your CPU and/or motherboard’s circuit board (PCB).
3.
The EK High Flow and EK-ACF type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubb er O-ring gaskets.
4.
The use of corrosion inhibiting coolants is always recommended for any liquid cooling system.
STEP 1: GENERAL INFORMATION.
Sample photo of GIGABYTE GeForce GTX 980 Ti WindForce 3X
and Gaming G1 series card.
STEP 2: PREPARING YOUR GRAPHIC CARD.
1. REMOVING STOCK COOLER AND BACKPLATE: Remove encircled
seven screw on the cooler.
STEP 2 cont.: PREPARING YOUR GRAPHIC CARD
1 cont. REMOVING STOCK COOLER
Remove all encircled screws. All heat sink assembly screws
should be removed, including self-adhesive washers on both sides of the PCB (if present). There are
up to 4 screws on the back of the graphics card.
2. CLEANING THE PCB.
Carefully detach the original stock cooler after
removing
all
screws securing it to the board. Wipe off the remains (by
using non–abrasive cloth or
q-tip
, as shown on sample photo) of the
original thermal compound until the components and circuit board are
completely clean. EKWB recommends the use of denatured alcohol for
removing TIM leftovers.
3. APPLYING THERMAL COMPOUND.
Wipe off the
remains (by using non–abrasive cloth or
q-tip
) of the
original thermal compound until the components and
circuit board are completely clean. Apply thermal
compound: lightly coat
NVIDIA
GPU chip with enclosed
EK-TIM Ectotherm thermal grease. EKWB recommends
to apply thermal grease in cross form for best
performance (see sample picture).
4. CUTTING THERMAL PADS.
Your block comes with thermal pads, some of which are already pre-cut. Others
have to be cut to smaller chunks in order to cover all the VRM components such as MOSFETs and drivers. PLEASE
REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION.
Replacement thermal pads:
Thermal Pad E – 0.5mm (RAM 8x)
Thermal Pad F – 1.0mm (120x16mm)
STEP 3: INSTALLING THE WATER BLOCK
1. PLACING THERMAL PADS ON PCB.
Place thermal pads on chips so that numbers on chips match size of thermal pads. EKWB made sure users have more than
enough pads to cover all surfaces that need to be covered to make block fully functional). EKWB recommends using small drops of electrically non-conductive (for
example: Arctic Cooling MX-2 ™, MX-4 ™ or GELID GC-Extreme™) thermal grease on each phase regulator (that is being covered with thermal pad) in order to even
further improve the thermal performance of the EK-FC980 GTX Ti WF3 series water block.
1
1
1
1
1
1
1
1
1
1
1
1:
Thermal pad E – 0.5mm
(for memory IC):
2:
Thermal pad F – 1.0mm
(for Vdd VRM/MOSFET):
1
2
