All disclosures, notices and warranty conditions are being written on the EKWB website. Please read terms of use. Released on 2
nd
of March, 2012. Revision 1.0
2. PLACING BLOCK TO GRAPHIC CARD
. Carefully position the water block with
preinstalled 2.5mm standoffs on to the graphics card. During this process please make sure
you align mounting holes on PCB with holes on the water block. Also pay attention not to
use too much force by pressing block down to PCB. Chip dies are prone to cracking.
3. ATTACHING BLOCK TO GRAPHIC CARD
. By using Philips screwdriver screw
in enclosed M3x4 DIN7985 screws. EKWB recommends start screwing the screws
around the GPU core and continue outwards. Always use a PVC washer under
each and every screw!
STEP 4: CHECKING FOR CONTACTS
Temporarilyremove the water block to check for uniform surface contact between the block and the components, pay special attention to the VRM section of the graphics card.
Check whether the water block makes contact with the VRM. In case you experience poor contact we highly recommend the use of EK-FC7950 Backplate (EAN: 3831109856277)
which will improve the situation. Note the pattern of contact on a piece of paper. Then repeat substeps in previous section to reattach the block.
In case you fail to obtain
good contact, please check again your thermal pad thickness or contact our support service.
STEP 6: FITTING POSITIONING
Screw in the fittings and plugs. Please use spacer only on copper base if you use fitting with G1/4 thread longer than 5mm (see sample picture). Use 6mm allen key to screw in
and tighten the EK-Plug G1/4. EKWB recommends using EK-PSC fittings with the EK-FC7950 series water blocks. To ensure that the tubes are securely attached to the
barb/fittings, please use hose clamps or an appropriate substitute.
You can use any opening as an inlet/outlet port.
STEP 6: INSERTING CARD IN YOUR PC CASE
Carefully lift your graphics card with installed block and insert it in your PC’s motherboard PCI-express expansion slot. Please bear in mind that your graphics card is probably
heavier than when it was equipped with original heat sink fan assembly. One needs to be very careful when handling the graphics card. Avoid all un-needed manipulation of the
VGA/water block assembly that might damage your card or water block during final installation.
STEP 5: OTHER INSTRUCTIONS
VERY IMPORTANT NOTICE:
Once the installation is completed, it is a recommended practice to test the cooling circuit for leaks prior to powering up the computer. We recommend a 24 hour leak test prior to powering
up the computer. Do not test the water block using tap water pressure. This will rupture the top of the housing and render the block unusable (and will void your warranty).While all efforts have been made to provide the
most comprehensive tutorial possible, EK Water Blocks assumes no liability expressed or implied for any consequential damage(s) occurring to your equipment as a result of using EK Water Blocks cooling products, either
due to errors or omissions on our part in the above instructions, or due to failure or defect in the EK Water Blocks cooling products.
WARRANTY:
Our products are warranted against defects in materials or workmanship for a period of 24 months beginning from the date of delivery to the final user. During this period, products will be repaired or have
parts replaced at our discretion provided that: (I) the product is returned to the agent from whom it was purchased; (II) the product has been purchased by an end user and has not used for commercial purposes; (III)
the product has not been misused, handled carelessly, or used in a manner other than in accordance with the instructions provided describing its installation and proper use. This warranty does not confer rights other than
those expressly set out above and does not cover any claims for consequential loss or damage. This warranty is offered as an extra benefit and does not affect your statutory rights as a consumer. This warranty is voided
if the product comes in contact with aggressive UV additives or other improper liquids.
REQUIRED TOOLS AND MOUNTING SCREWS:
scissors
philips screwdriver
9 × M3x4 DIN7985
9
×
PVC washers
thermal grease
Use 9 enclosed
PVC washers
underneath each
screw!
Use 9 screws M3x4
EK-PSC Fitting
Plug with o-ring
HI
G
H
FLOW
F
IT
TI
N
G
3mm spacer
Gasket/O-ring
High Flow
Fitting
EK
-PS
C
FI
TT
IN
G
