background image

1

www.automationdirect.com/click-plc

3505 HUTCHINSON ROAD 

CUMMING, GA 30040-5860 

1-800-633-0405

C2-02CPU Quick Start Guide 

Copyright© 2020, 

Automationdirect.com

 Incorporated/All Rights Reserved Worldwide

Before You Begin...

This guide provides a quick overview of installation and setup of your 
CLICK PLUS CPU. It assumes some familiarity with the installation 
and operation of industrial control equipment. 
Please read and understand the information in this guide prior to 
installation, operation, or servicing this equipment.

The CLICK PLUS User Manual provides full specifications and more 

in-depth information on installation, setup, 
programming and operation of the device. The 
User Manual (C2-USER-M) is available in PDF 
format by scanning this QR code or from 

https://

www.automationdirect.com/pn/doc/manual/
C2-USER-M

. Extensive online help is also 

available from within the CLICK software or at 

https://www.automationdirect.com/clickplcs/free-software/
software-help

.

What You’ll Need

 

ƒ

CLICK PLUS CPU

 

ƒ

PC, or Android or iOS mobile device (for setup/provisioning)

 

ƒ

Click Software ver. 3.00 or later (PC) or Click App (mobile device)

 

ƒ

24VDC power supply (SELV and Limited Energy)  
(CLICK power supply C0-00AC or C0-01AC is recommended.)

 

ƒ

Appropriate enclosure with vertical surface for DIN rail or surface mount

 

ƒ

M4 screws, spring washers and flat washers if surface mounting

 

ƒ

Ferrules and crimping tool for wire terminations (recommended)

 

ƒ

An Option Slot cover (part #C2-FILL) is recommended if you are not 
planning to use an Option Slot module. (Sold separately.)

 

ƒ

Basic tools (screwdriver, wire stripper, etc.)

PLEASE REVIEW THE SAFETY WARNINGS ON THE 

NEXT PAGE!

CLICK PLUS C2-02CPU

The CLICK PLUS C2-02CPU provides the 
full power of the CLICK PLUS CPU family, 
in a unit optimized for wireless connectivity. 
It offers both Wi-Fi and Bluetooth 
connection for simple wireless provisioning 
and connectivity with the CLICK Mobile 
app. The CPU is compatible with the full 
line of CLICK PLUS Option Slot modules 
and CLICK Stackable modules.

Key Features

 

ƒ

Real Time Clock/Calendar

 

ƒ

Battery backup (battery sold separately)

 

ƒ

micro-B USB port

 

ƒ

WLAN

 

ƒ

Bluetooth

Shown with optional C2-FILL  

slot cover (sold separately)

Summary of Contents for CLICK PLUS C2-02CPU











Reviews: