_ Electronic Ovens _ rev. 0 _______________________________________________________________ KF 1010 UD _
_________________________________________________________________________________________ page 17 _
4.
4.
4.
4.7
7
7
7
Periods without use
Periods without use
Periods without use
Periods without use
If the appliance is not used for a long time, it is good practice to unplug it from the mains (at
the magnetothermal safety switch upstream from the appliance) and to turn off the water with
the cut-of cock on the main supply line. It should be carefully cleaned inside the cooking
chamber and outside, taking special care to remove any salt deposits which would cause
corrosion to the steel surfaces.
We also advise protecting the appliance with an oily base spray (e.g. Vaseline oil), which
forms an effective protective film on the surface of the steel.
A suitable covering would also protect the appliance from the dust.
5
5
5
5.... Ma
Ma
Ma
Maintenance
intenance
intenance
intenance
5.1
5.1
5.1
5.1 General information
General information
General information
General information
A periodic control (at least once a year) of the appliance aids to guarantee long life and
correct operations.
Any sort of maintenance work on the appliance must be done exclusively by technically
qualified operators who have been trained in the maintenance work on this appliance.
Before beginning any sort of maintenance work on the appliance, turn the power supply off
(at the magnetothermal safety switch upstream from the appliance) and let it cool down.
The components that might require maintenance are all accessible by removing the left hand
side and the back of the unit.
5.2
5.2
5.2
5.2 Changing the lighting lamp in the cooking chamber
Changing the lighting lamp in the cooking chamber
Changing the lighting lamp in the cooking chamber
Changing the lighting lamp in the cooking chamber
The lamp is housed between the two door glasses; to replace it remove the external glass as
described in the paragraph: “Cleaning the door”.
Open the external glass, unscrew the 2 screws securing the lamp protection cover with the
appropriate tool and replace the lamp with another with the same specifications: 12V 35W
300°C (this is a halogen lamp and should not be touched with your bare hands)
5.3
5.3
5.3
5.3 Changing the door
Changing the door
Changing the door
Changing the door seal
seal
seal
seal
The door seal has a rigid profile with 4 fixing tabs. The profile must be fitted into the guide
on the face of the cooking chamber.
The rectangular seal fits perfectly into the frame of the guide and, therefore, the seal profile
fits perfectly onto the face of the cooking chamber.
To change the seal, remove the old one from the guide by pulling hard at the four corners.
Clean any dirt from the guide and introduce the new seal (to make this operation easier, we
advise dampening the seal profile with soapy water).
5.4
5.4
5.4
5.4 Changing the fuse
Changing the fuse
Changing the fuse
Changing the fuse
If the appliance is powered but no displays or leds are alight on the control panel, it could
mean that one of the fuse is of the printed circuit board (with microprocessor) is interrupted. To
reach the card, remove the left side of the appliance (unscrewing the 3 screws). The fuse holder
is clearly visible on the card. To change the fuse, press gently on the cap of the fuse hold and,
keeping it pressed, turn it slightly in an anti-clockwise direction to remove it. Replace the fuse
with another with the same specifications and then close the fuse holder cap by turning it in the
opposite direction.
5.5
5.5
5.5
5.5 Resetting the thermal breaker safety device
Resetting the thermal breaker safety device
Resetting the thermal breaker safety device
Resetting the thermal breaker safety device
This device (identified by the relative sticker) can be found on the back of the unit. Reset it by
pressing the red button fully down after unscrewing the protective cover and letting the oven
cool down. Once done, replace the protective cover.
