The new
‘Quick-Lock’
cable system allows a quick change of the machines (e. g. PTX - 500).
Safety advice:
•
Please pay attention to the safety instructions in the attached leaflet!
•
Do not pierce the motor housing as this could damage the double insulation (use adhesives).
•
Always pull the plug from the mains before making any settings or carrying out maintenance.
•
Only plug-in when machine is switched off.
•
Keep mains lead clear from working range of the machine. Always lead the cable away behind you.
•
Before use check machine, cable, and plug for any damages or material fatigue. Repairs should only be carried out
by authorised service agents.
•
After switch off, the machine will not be idle immediately. (After-running of the work spindle.)
Allow the machine to come to a stop before putting down.
•
Never reach into the danger area of the machine when it is running.
•
Always wear safety goggles and ear protectors when working with this machine. It is further recommended to wear safety gloves, apron, as
well as sturdy non-slipping shoes.
•
Always use the additional handle.
•
Always use the protecting cap when roughi ng- down and separating.
•
Only use tools whose permitted speed is at least as high as the highest no-load speed of the machine.
•
Pay attention to the dimensions of the grinding disc. The mounting hole diameter must fit the mounting flange without play.
Do not use reducer pieces or adapters.
•
Check grinding tools before use. The grindi ng tool must be properly mounted and turn freely.
Perform a test run for at least 30 seconds without load. Do not use damaged, out of round or vibrating grindi ng tools.
•
Immediately switch off the machine in case of considerable vibrations or if other malfunctions occur.
Check the machine in order to find out the cause.
•
Always use and store the grinding discs according to the manufacturer's instructions.
•
When grinding metal, flying sparks are produced. Take care that no persons are endangered. Because of the danger of fire,
no combustible materials should be located in the vicinity (spark flight zone). Do not use dust extraction!
•
Always hold the machine in a way that sparks or sanding dust fly in counter direction to your body.
•
Dust that arises when working in stones with crystalline silicic acid can damage your health. do not work on any material containing asbestos.
Please note the safety regulations, VBG, of the employer's liability insurance association.
•
Never use a cutting disc for grinding. Do not subject cutting discs to side pressure.
•
When separating stone the guide shoe must be used!
•
The adjusting nut must be tightened before starting to work with the machine.
•
The work piece must be fixed if it is not heavy enough to be steady. Never lead the work piece to the grinding disk with your hand.
•
In case of extreme operating conditions (e.g. when smoothing metals with the supporting disk and vulcanised fibre disks) strong contamina-
tion can build up inside the angle grinder.
In such cases it is recommended to shorten the cleaning cycles and/or add a residual current operated device.
VARILEX
®
WSF 900
Speed selection (AG 1300-125 XE)
Speed pre-selection with the setting wheel:
A = lowest speed
G = highest speed
M ounting the protective cover
Open the clamping lever. Push the protective cover over the gear neck, if necessary slightly
loosen the nut of the tension screw.
EASY -LOC K clamping nut
1. Secure the disc loosely and tighteen by hand using the EASY-LOCK clamping nut.
2. Press the spindle lock and tighten the disc by turning it clockwise by hand. That´s all!
3. To release the disc press the spindle lock and turn the disc anti-clockwise by hand.
Fitting the wor king tool
Always disconnect the plug from the socket before carrying out any work on the machine.
Maintenance
Keep the machine and the ventilation slots clean.
Only use Original accessories and spare parts. Should components which have not been de-
scribed need to be exchanged please contact one of our Atlas Copco service agents.
Service agents
Worldwide service by Atlas Copco. The corresponding addresses are to be found in the at-
tached brochur e.
Technical data
900 Watt, 220 – 240 V, 50 – 60 Hz. Continuous speed control by speedo generator (2000 -
5000 min
-1
) (constant number of revs). Weight approx . 1,8 kg.
Guarantee
A 12 month guarantee (as from invoice date) is given for all technical and mechanical parts,
except in the case of outside culpability.
Spares can be sup plied accord ing to the list. We will carry ou t necessary repairs.
Advice for operation
When grinding, do not press into the tool, but move it evenly to and fro on the work piece.
For best results, hold the disc at an angle of at least 30° to the working surface.