GB
- 32 -
•
For the horizontal clamping of workpieces you
can anchor the clamping device in the holder
(44).
•
To move out the workpiece supports (10)
press the lever on the bottom side of the
workpiece support and then pull the workpie-
ce support outwards to the right or left.
•
For repeat cuts of identical length you can
unfold the longitudinal stop (41).
•
When the locking grip (21) is undone, you can
tilt the machine head (4) to the left or right by
up to 45°.
•
To ensure that the saw is standing securely,
adjust the adjustable foot (13) by turning it so
that the saw stands in a horizontal and firm
position.
5.3 Adjusting the miter angle on the machine
head (Fig. 1a, 2, 6)
•
Undo the locking grip (21).
•
Hold the machine head (4) by the handle (1).
•
After pulling the button (33), the machine
head can be tipped infinitely as well as to se-
veral locking points.
•
Angles to the left: 0-45°
•
Angles to the right: 0-45°
•
Re-tighten the locking screw (21).
5.4 Precision adjustment of the stop for cros-
scut 90° (Fig. 7-10)
•
Fasten the turntable (17) in 0° position.
•
Undo the locking screw (21) and move the
machine head (4) all the way to the right using
the handle (1).
•
Place the 90° angular stop (a) between the
blade (7) and the turntable (17).
•
Open the counternut on the adjustment screw
(39).
•
Adjust the adjustment screw (39) until the
angle between the blade (7) and the turntable
(17) equals 90°.
•
Then tighten the counternut again.
•
Finally check the position of the pointer (20)
on the scale (19). If necessary, undo the poin-
ter (20) with a Philips screwdriver, set it to the
0° position on the scale (19) and retighten the
retainer screw.
•
No stop angle included.
5.5 Precision adjustment of the stop for miter
cuts 45° (Fig. 7-10)
•
Fasten the turntable (17) in 0° position.
•
Undo the locking screw (21) and move the
machine head (4) all the way to the left using
the handle (1), until it coincides at 45°.
•
Place the 45° stop angle (b) between the bla-
de (7) and the turntable (17).
•
Open the counternut on the adjustment screw
(37 or 38).
•
Adjust the adjustment screw (37 or 38) so
that the angle between the blade (7) and the
turntable (17) equals exactly 45°.
•
Then tighten the counternut again.
•
No stop angle included.
5.6 Adjusting the movable stop rails (Fig. 1,
10-14)
•
Important! This saw is equipped with movable
stop rails (9, 11) that are screwed to the fixed
workpiece stop (40).
•
For carrying out angle and miter cuts the mo-
vable stop rails must be adjusted to prevent a
collision with the saw blade.
•
For miter and angle cuts to the left, the left
stop rail must be moved outwards. For angle
cuts to the right, the right stop rail must be
moved outwards.
•
Undo the locking screws (43) on the movable
stop rails and pull the rails back so far that a
collision with the saw blade can be ruled out.
Prior to every cut retighten the locking screws
of the stop rails.
•
For cleaning purposes you can remove the
stop rails from the workpiece stop (40).
•
Always fasten the movable stop rails on the
equipment again after you have completed
your cleaning work.
5.7 Instalation E-Stand
Please follow for installing the E-Stand indica-
tions,
fi
g 23-39.
Anl_SA_TE_SM_2534_Dual_SPK8.indb 32
Anl_SA_TE_SM_2534_Dual_SPK8.indb 32
19.05.16 08:33
19.05.16 08:33