GB
- 25 -
Select the cutting height according to the length
of the grass. If the lawn has grown quite a bit,
mow over it several times so that no more than 4
cm of grass are cut at one time.
Switch o
ff
the motor before doing any checks on
the blade. Keep in mind that the blade continues
to rotate for a few seconds after the engine has
been switched o
ff
. Never attempt to manually
stop the blade. Regularly check to see if the
blade is securely attached, is in good condition
and is sharp. If the contrary is the case, sharpen
the blade or replace it. In the event that the blade
strikes an object, immediately switch o
ff
the lawn
mower and wait for the blade to come to a com-
plete stop. Then inspect the condition of the blade
and the blade mount. Replace any parts that are
damaged.
Lay the power cable on the ground in loops in
front of the power outlet. Mow away from the po-
wer outlet and cable, making sure that the power
cable always trails in the mowed grass so that the
lawn mower does not travel over the cable.
As soon as grass clippings start to trail the lawn
mower, it is time to empty the grass basket.
Important. Before taking o
ff
the grass basket,
switch o
ff
the engine and wait until the blade
has come to a stop.
To take o
ff
the grass basket, use one hand to lift
up the chute
fl
ap and the other to grab onto the
basket handle. Remove the basket. For safety
reasons, the chute
fl
ap automatically falls down
after removing the grass basket and closes o
ff
the
rear chute opening. If any grass remains in the
opening, it will be easier to restart the engine if
you pull the mower back approximately 1m.
Do not use your hands or feet to remove clippings
in or on the mower housing, but instead use suita-
ble tools such as a brush or a hand broom.
In order to ensure that the majority of grass clip-
pings are picked up, the inside of both the grass
basket and especially the net must be cleaned
after each use.
Reattach the grass basket only when the engine
is switched o
ff
and the blade is stopped.
Using one hand, lift up the chute
fl
ap, while grab-
bing onto the basket handle with the other. Hang
in the basket from the top.
8. Replacing the power cable
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
9. Cleaning, maintenance and
ordering of spare parts
Always pull out the power plug before starting any
cleaning work.
9.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
We recommend that you clean the equipment
immediately after you use it.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may be ag-
gressive to the plastic parts in the equipment.
Ensure that no water can get into the interior
of the equipment.
9.2 Servicing
•
Worn out or damaged blades, blade mounts,
and bolts should be replaced as a set by an
authorized professional in order to keep the
equipment in balance.
•
Do not clean the lawn mower with running
water, particularly with high-pressure water.
Ensure that all mounting components (i.e.
screws, bolts, nuts etc.) are always tightened
so that the equipment can be safely operated
at all times.
•
Frequently check the grass catch assembly
for signs of wear.
•
Replace excessively worn or damaged parts
immediately.
•
Store your lawn mower in a dry room.
•
In order to ensure that you enjoy your scarifier
for many years to come, all screwed parts, as
well as the wheels and axles, should be clea-
ned and lubricated.
•
Keeping your hand mower in good condition
not only ensures a long lifespan and high per-
formance, but also enables the equipment to
thoroughly cut your grass with minimal effort.
For best results, clean the lawn mower with a
Anleitung_RG-EM_1843_HW.indb 25
Anleitung_RG-EM_1843_HW.indb 25
14.10.11 09:41
14.10.11 09:41
Содержание RG-EM 1843 HW
