GB
- 33 -
The Micro fastener enables easy changing of the
polishing attachment.
Use the foamed plastic attachment to apply
the polishing agent (Fig. 7).
•
Make sure that the foamed plastic attachment
is free of any foreign bodies.
•
Spread the polishing paste evenly over the
polishing pad. Do not apply the polish directly
to the polishing surface.
•
Switch the polishing machine on and off only
when the polishing machine is resting on the
polishing surface.
•
Place the extension lead over your shoulder
and work first on the large, flat surfaces such
as the bonnet, boot lid and roof.
•
Keep your movements as regular as possible.
•
Important! Allow the polishing machine to
glide over the polishing surface. Do not exert
pressure!
•
Work next on the smaller surfaces (doors, for
example)
Use the
fl
eece attachment to
fi
nish o
ff
the
polishing (Fig. 8).
•
Make sure that the fleece attachment is free
of all foreign bodies.
•
Remove the layer of polish in the same order
as it was applied.
•
Important! Do not exert pressure on the poli-
shing machine!
Care tips
•
For optimum paintwork protection, you should
polish your car 2 to 3 times a year.
•
Wash your car at least every 2 weeks. Avoid
using household detergents as these can da-
mage the paintwork and remove the layer of
wax.
•
Wash your car with a clean sponge, working
from top to bottom.
•
Remove all insects, bird droppings and tar
stains from the paintwork daily.
•
If you use any window-cleaning agents, spray
them onto a cloth and not directly onto the
windows in order to prevent them wetting the
paintwork.
6.2 Using as a sanding machine
Use the supplied sanding attachments (Fig. 9) for
sanding purposes.
The Micro fastener enables easy changing of the
sanding attachments.
•
Place the whole surface area of the sanding
disk on the material.
•
Switch on the machine and move it with gent-
le pressure over the workpiece completely
circular movements or moving it to and fro
and up and down.
•
Use a coarse paper for coarse sanding and a
finer paper for finish sanding. You can find the
best paper for the job by means of testing.
6.3 Speed Control Display (Fig. 3)
Use the speed control to set the desired working
speed.
Press the “+” button to increase the speed.
Press the “-” button to decrease the speed.
Refer to the display (8) for the set speed. Set
speed = Display x 100
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
authorized after-sales service or similarly trained
personnel to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
8.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a quali
fi
ed electrician
and/or an authorized service agent.
Anl_SA_CC_PO_1100_1_E_SPK8.indb 33
Anl_SA_CC_PO_1100_1_E_SPK8.indb 33
29.04.2020 07:04:29
29.04.2020 07:04:29
