![background image](http://html1.mh-extra.com/html/einhell/40-104-72/40-104-72_original-operating-instructions_2370147020.webp)
GB
- 20 -
vessel. If you discover any damage, please con-
tact the customer service workshop.
Notice!
The condensation water from the pressure
vessel will contain residual oil. Dispose of the
condensation water in an environmentally
compatible manner at the appropriate collec-
tion point.
8.3 Safety valve (10)
The safety valve has been set for the highest per-
mitted pressure of the pressure vessel. It is prohi-
bited to adjust the safety valve or remove its seal.
Actuate the safety valve from time to time to en-
sure that it works when required. To do so, open
the screw cap of the valve while the tank is under
pressure. Once the screw cap has been fully ope-
ned you must pull it to let air escape through the
valve. Then screw the cap fully back in place.
8.4 Check the oil level at regular intervals
Place the compressor on a level and straight
surface. The oil level must be between the two
marks MAX and MIN on the oil oil level window
(Fig. 11).
Changing the oil: Recommended hydraulic oil:
SAE 15W/40 or an alternative of the same quality.
It should be re
fi
lled for the
fi
rst time after 100
hours of operation. Thereafter the oil should be
drained and re
fi
lled after every 500 hours in ser-
vice.
8.5 Changing the oil
Switch o
ff
the engine and pull the mains plug out
of the socket. After releasing any air pressure you
can unscrew the oil drainage screw (15) from the
compressor pump. To prevent the oil from running
out in an uncontrolled manner, hold a small metal
chute under the opening and collect the oil in a
vessel. If the oil does not drain out completely, we
recommend tilting the compressor slightly.
Dispose of the old oil at a drop-o
ff
point for
old oil.
When the oil has drained out, re-
fi
t the oil draina-
ge screw (15). Fill new oil through the oil
fi
ller ope-
ning (17) until it comes up to the required level.
Then replace the oil sealing plug (14).
8.6 Cleaning the intake
fi
lter (1)
The intake
fi
lter prevents dust and dirt being
drawn in. It is essential to clean this
fi
lter after at
least every 300 hours in operation.
A clogged intake
fi
lter will decrease the
compressor‘s performance dramatically. Undo the
screw on the air
fi
lter so that the halves of the air
fi
lter housing can be opened. Use compressed
air at low pressure (approx. 3 bar) to blow out all
the parts of the
fi
lter and then assemble the
fi
lter
in reverse order. When cleaning, take adequate
precautions against dust (e.g. use a suitable face
mask).
8.7 Storage
Warning!
Pull the mains plug out of the socket and ventilate
the appliance and all connected pneumatic tools.
Switch o
ff
the compressor and make sure that it is
secured in such a way that it cannot be started up
again by any unauthorized person.
Warning!
Store the compressor only in a dry location
which is not accessible to unauthorized per-
sons. Always store upright, never tilted!
Store the equipment and accessories in a dark
and dry place at above freezing temperature. The
ideal storage temperature is between 5 and 30
°C. Store the electric tool in its original packaging.
8.8 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.Einhell-Service.com
9. Disposal and recycling
The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council o
ffi
ces.
Anl_TE_AC_400_50_10_V_SPK9.indb 20
Anl_TE_AC_400_50_10_V_SPK9.indb 20
06.07.2021 09:59:24
06.07.2021 09:59:24
Содержание 40.104.72
Страница 111: ...RUS 111 Anl_TE_AC_400_50_10_V_SPK9 indb 111 Anl_TE_AC_400_50_10_V_SPK9 indb 111 06 07 2021 09 59 35 06 07 2021 09 59 35...
Страница 150: ...GR 150 Anl_TE_AC_400_50_10_V_SPK9 indb 150 Anl_TE_AC_400_50_10_V_SPK9 indb 150 06 07 2021 09 59 38 06 07 2021 09 59 38...
Страница 161: ...161 Anl_TE_AC_400_50_10_V_SPK9 indb 161 Anl_TE_AC_400_50_10_V_SPK9 indb 161 06 07 2021 09 59 39 06 07 2021 09 59 39...