Eiki EK-450U Скачать руководство пользователя страница 27

Страница: 27 / 90

—

DLP Projector — Owner’s Manual

Remote Control Operating Range

The remote control uses infrared transmission to control the projector. It is not necessary to point the

remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the

rear of the projector, the remote will function well within a radius of about 10 meters (32.8 feet) and 30

degrees above or below the projector level. If the projector does not respond to the remote control, move

a little closer.

Projector and Remote Control Buttons

The projector can be operated using the remote control or the buttons on the rear of the projector. All

operations can be carried out with the remote control; however, the buttons on the projector are limited in

use.

Remote Control Code

The 100 different remote control codes (Remote ID, Code 00 - Code 99) are assigned to this projector.

Switching the remote control codes prevents interference from other remote controls when several

projectors or video equipment next to each other are being operated at the same time. Change the remote

ID on both projector and remote control.

To change the remote ID for the Remote Control:

Press and hold the [Remote ID] button for more than 3 seconds, and the LED indicator (above the [Off]

button of the remote control unit) starts blinking slowly.
Then, input the number between 00-99 by pressing the [0]~[9] buttons to switch the remote ID within 10

seconds.

After entering 2 digit of remote ID, the LED indicator will flash quickly for 3 times that indicates the remote

ID was changed.
Default setting: 00

evIce

ype

emote

Remote Control Unit

.... 99

Projector

00-99

..... 99

To change the remote code for the projector:

Press the [Menu] button to open the OSD menu. Press the [

]/[

] button to select

Setup

and press the

[Enter] button to enter the

Setup

menu.

Press the [

]/[

] button to select

Remote Settings

, and press the [Enter] button to enter the

Remote

Code

submenu.

Press the [

]/[

] button to select

Remote Code

, then choose the number (00-99) by pressing the [

]/[

]

button to set up the remote code.
Default setting: 00

To reset the remote ID:

Press the [Remote All] button for 3 seconds, and the LED indicator will flash quickly for 3 times that

indicates the remote ID was reset to default (00).

Содержание EK-450U



























































































Результаты поиска

Содержание EK-450U

Отзывы:

Похожие инструкции для EK-450U

Бренды по названию

Популярные бренды

Eiki EK-450U, Руководство пользователя

Результаты поиска

Содержание EK-450U

Отзывы:

Похожие инструкции для EK-450U

Бренды по названию

Популярные бренды