manualshive.com logo in svg

EFI E-36A, Инструкция по установке и обслуживанию, Страница: 25 / 129

Поделиться
Скачать
EFI E-36A Скачать руководство пользователя страница 25

25 

Installation and Service Guide: Color Controller E-36A

Installing Hardware

After power on, the site administrator should perform Network Setup, verify the network connection, verify that the 

E-36A appears in the list of printers, and then print  a few test documents from a networked computer that will use the 

E-36A. For more information, see 

Configuration and Setup

, which is part of the user documentation set.

Enabling the power synchronization with printer

During the installation, you can enable the power synchronization feature by using the USB power cable included in 

the accessory kit and OFF/ON switch on the back of the E-36A. The default switch position is OFF. 

When you enable power synchronization, the E-36A synchronizes power with the printer’s main power off/on status. 

If the printer powered off, the E-36A receives signals from the printer through the USB power cable, and automatically 

starts the shutdown process. If the printer is powered on, the E-36A receives the startup signals from the printer, and 

automatically powers on and begins the startup sequence. 

To enable the power synchronization feature at the E-36A

1

Make sure that the E-36A and the printer are powered off.

2

Make sure that the power synchronization switch on the back of the E-36A is in OFF position.

3

Remove the port cover that is attached to the Type B USB port on the back of the E-36A.

4

Locate the USB power cable in the accessory kit shipped with the E-36A.

5

Connect one end of the USB power cable to the Type B USB port on the back of the E-36A (see 

Figure  9

).

6

Connect the other end of the USB power cable to the USB port on the printer.

After the power synchronization is enabled, make sure to control the E-36A power using the 

printer.

Содержание E-36A


































































































































Отзывы:

Нет отзывов