manualshive.com logo in svg

EFI E-36A, Инструкция по установке и обслуживанию, Страница: 12 / 129

Поделиться
Скачать
EFI E-36A Скачать руководство пользователя страница 12

12 

Installation and Service Guide: Color Controller E-36A

Introduction

•

E-36A documentation, including the customer media pack and any related service bulletins

Precautions

This section includes information about how to safely operate and service the E-36A and how to avoid damage to E-

36A components.

Report shipping damage

If there is evidence of shipping damage, save the shipping boxes and damaged parts. Call the shipper immediately to 

file a claim and notify your authorized service/support center.

Do not change an existing network

The E-36A is probably connected to an existing Local Area Network (LAN) based on Ethernet hardware. The network 

is the link between the customer’s computer, existing laser printers, and other prepress equipment. Never disturb the 

LAN by breaking or making a network connection, altering termination, installing or removing networking hardware 

or software, or shutting down networked devices without the knowledge and express permission of the site 

administrator.

Do not assign an IP address to the E-36A

Only the site administrator should assign an IP address to a network device, including the E-36A. If you enter an 

incorrect IP address for the E-36A, errors may occur on connected devices.

Handling boards

When handling a printed circuit board, do not bend it. Hold it by opposing edges, rather than by the corners.

Handling the hard disk drive

To ensure that you do not damage the hard disk drive, do the following:

•

Follow electrostatic discharge (ESD) precautions.

•

Keep magnets and magnetic-sensitive objects away from the hard disk drive.

•

Do not loosen or remove the screws on the top of the hard disk drive. Doing so voids the warranty.

•

Handle the hard disk drive by its sides and avoid touching the printed circuit board.

•

Do not drop, shake, or bump the hard disk drive.

•

Before you remove or install a hard disk drive, allow it to reach room temperature.

Avoid magnets

Keep magnets and magnetic-sensitive objects away from electronic components, especially the hard disk drive.

Avoid touching magnetic tools to storage media such as hard disk drives. Contact between 

magnetic tools and magnetic storage media may result in data corruption.

Содержание E-36A


































































































































Отзывы:

Нет отзывов