background image

GENERAL SAFETY

The “Eemax ProAdvantage” heater is specifically designed to take in cold or hot water and 
heat it up to a maximum of 140F (60C).  To obtain optimum performance and energy savings, 
the unit should be located as near as possible to the point of use.  

The unit is supplied with a ¾” NPT pipe connection.  

Under no circumstances 

use a blow 

torch on pipes which are connected to or near these heaters.  Carefully use Teflon  tape 
where necessary ensuring no debris will enter the unit.  

Do not use a pipe dope.

Ensure that all the pipes are clear of debris before fitting the heater.

THIS UNIT HAS TWO 

DEDICATED INDEPENDENT 240V 

OR

277V 

CIRCUITS. 

USE CORRECTLY RATED WIRES AND CIRCUIT BREAKERS.  
U.L. 499, 18.4. - THE RATING OF THE BRANCH-CIRCUIT OVERCURRENT 
PROTECTIVE DEVICE SHALL BE 150% OF THE RATING OF THE PRODUCT.

DO NOT USE SPACE SAVING BREAKERS

.

FAILURE TO 

GROUND

THE SYSTEM MAY RESULT IN DEATH OR SERIOUS INJURY.

WARNING

THIS UNIT HAS TWO DEDICATED INDEPENDANT POWER CIRCUITS.   

DISCONNECT BOTH POWER CIRCUITS BEFORE SERVICING.

DO NOT USE SPACE SAVING BREAKERS

.

WARNING

IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE, OR MAINTENANCE,
MAY CAUSE

DEATH, SERIOUS BODILY INJURY, OR PROPERTY DAMAGE

. REFER TO 

THIS MANUAL FOR ASSISTANCE OR CONSULT THE LOCAL ELECTRIC UTILITY FOR 
FURTHER INFORMATION.

WARNING

WATER HEATERS ARE EQUIPPED FOR ONE VOLTAGE ONLY:  

THIS WATER HEATER IS

EQUIPPED FOR THE VOLTAGE DISPLAYED ON THE MODEL RATING PLATE.  DO NOT
USE THIS WATER HEATER WITH ANY OTHER VOLTAGE OTHER THAN THE ONE
SHOWN ON THE MODEL RATING PLATE.  FAILURE TO COMPLY WITH THIS MAY RESULT
IN DEATH, SERIOUS BODILY INJURY, AND/OR PROPERTY DAMAGE. IF YOU HAVE ANY
QUESTIONS OR DOUBTS CONSULT EEMAX OR YOUR LOCAL ELECTRIC COMPANY.

WARNING

HAZARD OF ELECTRICAL SHOCK!

BEFORE REMOVING THE COVER OR SERVICING THE 

WATER HEATER, MAKE SURE ALL ELECTRICAL SOURCES TO THE WATER HEATER ARE
TURNED “OFF”.   FAILURE TO DO THIS MAY RESULT IN

DEATH, SERIOUS BODILY INJURY,

OR PROPERTY DAMAGE

NOTE:  THIS UNIT HAS TWO INDEPENDENT DEDICATED ELECTRICAL POWER 

CIRCUIT CONNECTIONS.

2

Содержание PA014240











Отзывы: