background image

ELECTRIC INSTANTANEOUS WATER HEATER

INSTALLATION GUIDE AND OWNER’S MANUAL

EEMAX

ProAdvantage Series 

PA  

240 - * 

1Φ 240V - Series 2

PA  

277 - * 

1Φ 277V - Series 2  

READ THE GENERAL SAFETY SECTION AND THE ENTIRE MANUAL BEFORE 
INSTALLING OR OPERATING THIS WATER HEATER.   FAILURE TO FOLLOW 
THE SAFETY RULES MAY CAUSE THE UNIT TO OPERATE IMPROPERLY, 
WHICH COULD LEAD TO  DEATH, SERIOUS BODILY INJURY AND/OR 
PROPERTY DAMAGE.  READ THE ENCLOSED WARRANTY CARD. WARRANTY 
OF THIS WATER HEATER WILL DEPEND ON PROPER INSTALLATION AND 
OPERATION. THE WARRANTY SHALL BE VOID IF THE DESIGN HAS BEEN 
ALTERED. THE MANUFACTURER OF THIS HEATER WILL NOT BE LIABLE FOR 
ANY DAMAGES BECAUSE OF FAILURE TO COMPLY WITH THE INSTALLATION 

WARNING

MODELS 

COVERED: 

IF YOU REQUIRE ANY HELP OR HAVE ANY QUESTIONS RELATING TO THE
INSTALLATION OR PERFORMANCE OF THIS HEATER, PLEASE CALL OUR 
TECHNICAL SERVICE DEPARTMENT TOLL FREE : 1-800-543-6163.

HAVE THE INFORMATION LISTED BELOW WHEN CALLING :

S/N __________ MODEL # _____________________INSTALL DATE__________

ANY DAMAGES BECAUSE OF FAILURE TO COMPLY WITH THE INSTALLATION 
AND OPERATING INSTRUCTIONS OUTLINED ON THE FOLLOWING PAGES. 

THE INSTALLATION MUST CONFORM TO THE INSTRUCTIONS IN
THIS MANUAL; ELECTRIC COMPANY RULES; AND LOCAL CODES, OR IN
THE ABSENCE OF LOCAL CODES, WITH THE LATEST EDITION OF THE
NATIONAL ELECTRICAL CODE. THESE PUBLICATIONS ARE AVAILABLE FROM
YOUR LOCAL GOVERNMENT, PUBLIC LIBRARY, OR ELECTRIC COMPANY.

1

THIS UNIT HAS TWO INDEPENDANT DEDICATED POWER CIRCUITS.   

DISCONNECT BOTH POWER CIRCUITS BEFORE SERVICING. 

Содержание PA014240











Отзывы: