Edwards D395-90-000 Скачать руководство пользователя страница 2

Страница: 2 / 36

This product has been manufactured under a quality management system certified to ISO 9001:2008

Declaration of Conformity

We, Edwards

Limited,

Crawley Business Quarter,

Manor

Royal,

Crawley,

West Sussex, RH10 9LW, UK

declare under our sole responsibility, as manufacturer and person within the EU authorised

to assemble the technical file, that the product(s)

Active Digital Controller – Standard version

D395-90-000

Active Digital Controller – Enhanced version

D395-91-500

to which this declaration relates is in conformity with the following standard(s) or other
normative document(s)

EN61010-1: 2010

Safety Requirements for Electrical Equipment for Measurement,

Control and Laboratory Use. General Requirements

EN61326-1:2013

Electrical equipment for measurement, control and laboratory

(Class B Emissions,

Use. EMC requirements. General requirements

Industrial Immunity)

EN50581:2012

Technical Documentation for the Assessment of Electrical and

Electronic Products with respect to the Restriction of Hazardous

Substances

Following the provisions of

2014/35/EU Low

Voltage

Directive

2014/30/EU

Electromagnetic Compatibility (EMC) Directive

2012/19/EU

Waste from Electrical and Electronic Equipment (WEEE) Directive

2011/65/EU

Restriction of Certain Hazardous Substances (RoHS) Directive

Note: This declaration covers all product serial numbers from the date this Declaration was

signed onwards.

16.07.2015, Eastbourne

Larry Marini, Senior Technical Manager

Date and Place

P200-03-720 Issue

Содержание D395-90-000































Результаты поиска

Содержание D395-90-000

Отзывы:

Похожие инструкции для D395-90-000

Бренды по названию

Популярные бренды

Edwards D395-90-000, Инструкция по эксплуатации

Результаты поиска

Содержание D395-90-000

Отзывы:

Похожие инструкции для D395-90-000

Бренды по названию

Популярные бренды