Edwards D395-90-000 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 36

background image

© Edwards Limited 2010. All rights reserved.

Page 11

Edwards and the Edwards logo are trademarks of Edwards Limited.

OPERATION

D395-90-880 Issue E

4

OPERATION

4.1

Front panel description

Figure 10 - Front panel displays

4.2

Power up

When you apply power to the ADC, all LEDs in the display will light for 2 seconds to confirm operation. The software
version will then be displayed for a further 2 seconds, in the format "AdCxx". If you need to contact Edwards for
support regarding the ADC, please have this software version number available.

4.2.1

Return to Factory Defaults

The ADC can be reset to factory defaults by holding the “UP” key before you apply power to the ADC, and continuing
to hold it throughout the startup process. The startup screens will be displayed and then “Err01” will be shown to
confirm successful reset. Disconnect all connected gauges and power cycle to clear this message.

Table 6 - Front panel symbols and their functions

Symbol

Name

Function

UP

Move to previous selection.
Cycle selected numerical values up.

DOWN

Move to next selection.
Cycle selected numerical values down.

ENTER

Turn the selected gauge on or off.
Edit the selected numerical item.
Move to the next digit of a numerical value.

ADC standard front panel

ADC enhanced front panel

«
...
15
16
17
18
19
...
»

Содержание D395-90-000





































Отзывы:

Нет отзывов

Похожие инструкции для D395-90-000

Бренд: IBM Страницы: 12

Бренд: K&K Страницы: 10

Бренд: Federal Signal Corporation Страницы: 60

Бренд: FASTRON. Страницы: 16

Бренд: Van Air Страницы: 4

Бренд: ICM Controls Страницы: 2

Бренд: Uniden Страницы: 28

Бренд: UniFocus Страницы: 23

Бренд: UniFocus Страницы: 6

Бренд: Vacon Страницы: 50

Бренд: V2 Страницы: 116

Бренд: V2 Страницы: 8

Бренд: V2 Страницы: 25

Бренд: V2 Страницы: 124

Бренд: WAREMA Страницы: 112

Бренд: WAGO Страницы: 414

Бренд: V2 Страницы: 48

Бренд: V2 Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды