EDU-TOYS CIRCUIT MAKER Skill Builder 125 Скачать руководство пользователя страница 51

Страница: 51 / 64

Project #102

Project #101

Sing & Fling

Power Pitch

WARNING:

Moving parts. Do not touch the fan or

motor during operation.

WARNING:

Do not lean over the motor.

WARNING:

Moving parts. Do not touch the fan or

motor during operation.

WARNING:

Do not lean over the motor.

-50-

In the circuit, the outputs from the alarm and music ICs are connected

together. Build the circuit shown and then place the alarm IC (U2)

directly over the music IC (U1), resting on two 1-snaps and a 2-snap.

Turn on the slide switch (S1) and you will hear a siren and music

together while the lamp (L1) varies in brightness. Push the press

switch (S2) and the fan spins, while the sound may not be as loud. The

fan may rise into the air when you release the switch.

In the circuit, the outputs from the alarm (U2) and music ICs are

connected together. Build the circuit shown and then place the alarm

IC (U2) directly over the music IC (U1), resting on three 1-snaps. Turn

on the slide switch (S1) and you will hear a siren and music together.

Push the press switch (S2) and the fan spins, while the sound may not

be as loud. The fan may rise into the air when you release the switch.
This circuit is similar to Project #101, but the fan will fly a little higher

since the sound circuit no longer drives the lamp (L1) and therefore

uses less battery power.

CM-125_Manual_031514.qxp_CM-125_Manual_031514 4/2/14 12:20 PM Page 51

Содержание CIRCUIT MAKER Skill Builder 125

































































Результаты поиска

Содержание CIRCUIT MAKER Skill Builder 125

Отзывы:

Бренды по названию

Популярные бренды

EDU-TOYS CIRCUIT MAKER Skill Builder 125, Инструкция по эксплуатации

Результаты поиска

Содержание CIRCUIT MAKER Skill Builder 125

Отзывы:

Бренды по названию

Популярные бренды