EDU-TOYS CIRCUIT MAKER Skill Builder 125 Скачать руководство пользователя страница 39

Страница: 39 / 64

Project #70

Pop On, Pop Off

Project #71

Little R Rules

Project #72

Big R Rules

The speaker uses electromagnetism to create

changes in air pressure, which your ears feel

and interpret as sound. Think of the speaker

as creating pressure waves in the air just like

waves in a pool. You only see waves in the

pool when you disturb the water, so the

speaker only makes sound when the voltage

changes.

-38-

Turn the slide switch (S1) on and off several times. You hear static from

the speaker (SP) when you turn off the switch.

Turn on either or both switches

and

compare

the

LED

brightness.
This circuit has the 100

and

resistors (R1 and R2)

arranged in parallel. You can

see that the smaller 100

resistor controls the brightness

in this arrangement.

Turn on either or both switches

and

compare

the

LED

brightness.
This circuit has the 100

resistor (R1), the 1K

resistor

(R2), and the photoresistor (RP)

arranged in series. You can see

that the larger photoresistor

limits the brightness in this

arrangement (the resistance of

the photoresistor will be much

higher than the others, unless

the light is very bright).

CM-125_Manual_031514.qxp_CM-125_Manual_031514 4/2/14 12:19 PM Page 39

Содержание CIRCUIT MAKER Skill Builder 125

































































Результаты поиска

Содержание CIRCUIT MAKER Skill Builder 125

Отзывы:

Бренды по названию

Популярные бренды

EDU-TOYS CIRCUIT MAKER Skill Builder 125, Инструкция по эксплуатации

Результаты поиска

Содержание CIRCUIT MAKER Skill Builder 125

Отзывы:

Бренды по названию

Популярные бренды